Gdf520psjoss Parts

This replacement O-Ring restores a watertight seal at an internal dishwasher connection, helping stop leaks and protect surrounding cabinetry. Replace a hardened, cracked, or flattened seal to maintain reliable wash performance and prevent water damage.

• Creates a watertight seal between mating parts inside the dishwasher
• Helps prevent drips and leaks during fill, wash, and drain cycles
• Addresses leaks caused by a worn, flattened, or damaged seal
• Visual clues: cracks, brittleness, deformation, or mineral trails at the joint

• Disconnect power and shut off the water supply before servicing
• Access the affected connection and remove the old O-ring
• Clean the groove and mating surfaces; lightly lubricate with food-grade silicone grease; seat evenly without twisting or pinching
• Reassemble and run a brief test cycle to check for leaks

This upper wash impeller circulates water to the upper spray system during the wash cycle, helping deliver thorough cleaning across dishes on the upper rack and throughout the tub.

• Drives water flow to the upper spray arm/manifold
• Worn or damaged impeller can cause weak spray, poor cleaning, or longer cycle times
• Physical damage (warping, cracks, stripped splines) warrants replacement

• Disconnect power and water before servicing
• Access is typically through the sump/pump area; note impeller orientation during removal
• Inspect mating parts (seal, hub, shaft/splines) and replace if worn
• Hand-tighten fasteners to OEM guidance and verify free rotation before reassembly

Size: 8-18 AB TSQ 5/8 SS

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

This fill funnel assembly mounts inside the dishwasher tub at the water inlet. It directs incoming water into the tub and helps prevent splashing or leaks at the fill area for reliable fills and cleaner operation.

• Channels water from the inlet opening directly into the tub
• Helps control splash and seal the fill port to reduce drips
• Damage, cracks, or a missing funnel can cause leaks near the fill area during the fill cycle or unusual spraying sounds
• Restores proper water entry path for consistent filling

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the fill inlet on the tub wall
• Remove retaining fastener(s) or tabs, replace the funnel, and ensure any seal is properly seated
• Reassemble and run a brief fill/rinse to check for leaks at the inlet area

The Funnel Service Kit is an OEM replacement part for GE dishwashers. It includes a water inlet funnel and seals necessary for proper water flow within your dishwasher. This part helps prevent leaks and ensures that water is properly directed into the dishwasher.

Symptoms of a faulty water inlet funnel service kit include:

• Water leaks from the dishwasher
• Insufficient water flow during the wash cycle
• Inconsistent cleaning or rinsing performance

Causes of a bad water inlet funnel service kit can include wear and tear over time, blockage from debris or mineral buildup, or damage to the funnel or associated components. If you notice issues such as water leaks, inadequate water flow, or inconsistent cleaning results, it may be time to replace the old or damaged water inlet funnel service kit with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This heater nut secures the dishwasher's heating element where it passes through the tub, helping maintain a tight connection and proper positioning. Replacing a damaged or missing nut can help prevent leaks and keep the element stable.

• Fastens the heating element to the tub from below to hold it firmly in place
• Helps support a watertight connection at the element pass-through when used with the proper seal
• Replace if the nut is cracked, heat-damaged, stripped, or missing
• Common symptoms include water leaking under the unit near the heater terminals and a loose or wobbly heating element

• Disconnect power at the breaker and shut off water before servicing
• Access the nut from beneath the dishwasher; remove the toe-kick and pull the unit forward if needed
• Support the element from inside the tub while tightening; snug gently and do not overtighten to avoid damage
• Restore power/water and run a short cycle to check for leaks

This clip bracket attaches to the dishwasher rack to secure a rack-mounted component or accessory. Replace a cracked or missing bracket to keep parts firmly in place so the rack loads easily and performs as designed.

• Attaches to the rack to hold the mating part securely in place
• Helps prevent shifting, rattling, or accessories falling off during cycles
• Restores proper fit when the original clip is broken, worn, or missing
• Typical signs: accessory won't stay attached, clip is visibly cracked or missing, loose components during operation

• Disconnect power at the breaker and turn off the water supply
• Pull out the rack to access the clip location
• Release the old clip's locking tabs and remove; align and snap the new clip firmly in place
• Verify a secure fit before reinstalling the rack and running a test cycle

This detergent cup cover attaches to the dishwasher's dispenser to seal the detergent compartment until the control releases it. Replacing a damaged cover prevents early washout and restores consistent detergent release for reliable cleaning results.

• Covers and seals the dispenser's detergent cup
• Opens at the proper time to release detergent into the wash
• Helps prevent detergent leaking or washing out too early
• Typical symptoms: cup won't stay closed, poor cleaning, visible damage to the cover/hinge

• Disconnect power to the dishwasher before servicing
• Handle hinge tabs carefully; transfer and tension the existing spring/pin if your model uses them
• After installation, close and manually release the cover to ensure smooth operation before running a cycle

The Rack Slide is an OEM replacement part for GE dishwashers. It refers to the components that allow the upper rack to glide smoothly in and out. Allowing for continuous movement over extended use, the slides can degrade, causing friction or binding that restricts access to dishes.

Symptoms of bad rack slides include:

• Difficulty fully extending or retracting the racks   
• Noisy operation accompanied by grinding or squeaking noises
• Racks that do not run smoothly and become stuck partially open

Causes of rack slides becoming bad are normal wear and tear from loading and unloading dishes over many years. Motion parts wear out more quickly than stationary components.

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

Replace a worn or broken tub roller with this Tub Roller and Stud Assembly. It mounts to the dishwasher tub wall to guide the rack smoothly, preventing dragging, binding, or derailment when loading and unloading.

• Mounts on the tub sidewall to provide a smooth glide point for the dish rack
• Restores easy rack movement and can reduce squeaking or scraping noises
• Helps keep the rack aligned and prevents it from jumping off track
• Typical signs of failure: cracked/broken wheel, missing/bent stud, rack difficult to slide

• Disconnect power and water supply before servicing; wear cut-resistant gloves.
• Pull the rack out to access the roller location inside the tub.
• Remove the old roller and stud (retainer/tab/screw varies by model) and install the new assembly in the same orientation.
• Slide the rack in and out to confirm smooth movement before returning the appliance to service.

This replacement flood stem holds and guides the washer's water-level float so the machine can detect and control water levels. Replaces a worn or damaged mounting tube to restore reliable float operation. What it does:

• Secures and positions the water-level float inside the tub or housing
• Allows the float to move freely so the machine senses proper water level
• Helps prevent overfill and incorrect fill-level behavior when functioning correctly
• Common symptoms of a faulty unit: incorrect water level, washer overfills or fills unevenly, or the machine shows fill/drain issues

• One flood stem

• Disconnect power and turn off the water supply before starting any repair
• Replacement typically requires access to the washer cabinet/top or inner tub area
• Handle the float and tube gently to avoid damage; ensure proper seating and alignment during reassembly
• After installation, run a short fill/drain cycle to confirm correct float operation and that there are no leaks

This arm hinge assembly restores smooth, controlled movement of a hinged component in your dishwasher, helping maintain proper alignment and reliable operation. Replacing a worn or broken hinge can reduce binding, squeaks, and misalignment that affect performance. What it does:

• Provides the pivot point and support for a hinged assembly
• Maintains alignment to ensure correct engagement and sealing
• Helps ensure smooth opening/closing motion without binding
• Replaces a hinge arm that is cracked, bent, or worn
• Common signs: stiff or uneven movement, squeaking or popping noises, misalignment, or visible damage

• 1 arm hinge assembly

• Disconnect power and water before servicing
• Support the door or movable assembly to relieve tension while removing the hinge
• Note orientation and transfer any side-specific hardware from the original part
• After installation, check for smooth motion and proper alignment before restoring power and water

Arm hinge assembly is the pivoting hinge that supports and guides the appliance door, restoring smooth, stable opening and closing for proper alignment and operation. Replacing a worn hinge helps stop sagging, misalignment, and scraping noises. What it does:

• Supports the door pivot and maintains proper hinge alignment for smooth opening/closing.
• Helps the door latch and seal correctly by keeping the door level and aligned.
• Common symptoms: door hangs or sags, door won't close or latch, rubbing or scraping noises during movement.
• Replaces a bent, worn, or broken hinge arm to restore normal door operation.

• Disconnect power before starting any service.
• Use proper hand tools and support the door while removing/installing the hinge to avoid damage or injury.
• Align the hinge and operate the door several times before fully tightening fasteners; follow manufacturer torque/fastening guidance if available.

The Silverware Basket is an OEM component specifically designed for GE dishwashers. It provides a separator zone to organize knives, forks, and spoons for effective cleaning. Plastic baskets endure exposure to hot water and chemicals with each cycle. Over years of usage, the plastic material can weaken or crack.

Symptoms of a bad silverware basket include:

• Loose or sagging support mesh that allows utensils to shift positions
• Cracks along welded seams where pieces connect
• Missing divider tabs or prongs used to organize different utensils 

Causes leading to failure are typically repetitive stresses from loading and unloading of silverware, along with chemical degradation speeding up plastic fatigue.

Replace yours today with this genuine GE OEM part to maintain proper wash and rinse water flow around delicates. Proper basket organization is key for cleaning performance. This GE replacement part is compatible with some Hotpoint, RCA, and Kenmore models.