Gdf540sh0ss Parts

Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.

Genuine Ge part

Hose Wash Pump Inlet

5.0 (2)

By: Ge

Part Number: WD24X10059

Do-It-Yourself Stories from Customers like You The water is not spraying. The circulation pump stopped working. Kevin G. • Saucier , MS • September 04, 2022

I have the GE Cafe Dishwasher - CDT725SSF0SS. The circulation pump went out so no water was spraying into the dishwasher. This kit has everything needed to install a new circulation pump. Because the new pump has a different electrical connection, you'll also need to replace the wiring harness and discharge pump - but the kit contains all the parts including clamps. I am not sure why a new fine filter was included - it didn't fit my model dishwasher and had nothing to do with the issue I... Read more

Genuine Ge part

Panel Control Asm

By: Ge

Part Number: WD34X11836

Genuine Ge part

Kit Hinge Asm Rh

By: Ge

Part Number: WD35X20485

Note: Right side hinge

Genuine Ge part

Insulation Tub Blanket

By: Ge

Part Number: WD01X20187

Genuine Ge part

Heating Element Washer

By: Ge

Part Number: WD1X1168

Genuine Ge part

Harness Asm Jumper

5.0 (1)

By: Ge

Part Number: WD21X10541

Do-It-Yourself Stories from Customers like You Wire harness did not function properly only intermittent contact Ernie C. • Rensselaer Falls , NY • April 23, 2014

Ordered new part and it was exactly what I needed to fix the problem. Read more

Genuine Ge part

Panel Control Asm

5.0 (1)

By: Ge

Part Number: WD34X20133

Do-It-Yourself Stories from Customers like You Panel was cracked Jay Z. • Brookfield , WI • August 26, 2019

It went well. Have to remove the door and there are 4 screws on the bottom of the door. Read more

Genuine Ge part

Spray Arm Kit

5.0 (27)

By: Ge

Part Number: WD35X10393

Contains one lower spray arm and one middle spray arm.

Do-It-Yourself Stories from Customers like You Dishwasher was not heating water and dishes were coming out wet and cold no steam at all James C. • Lubbock , TX • February 15, 2019

I followed the directions on several websites for repairs. The obvious place to start is the heating coil and thermostat. I checked the continuity of the coil and it was good with a reading of almost zero resistance. Next I read that there is no thermostat controls on my GE dishwasher so I followed another webpage that said the Sensor Turbidity Assembly acts like a thermostat so I replaced that. Wasted effort as that switch sensor was OK. Normally it has a light on when it is working, a... Read more

Genuine Ge part

Pump Drain Kit

By: Ge

Part Number: WD35X20553

Genuine Ge part

Tine Block Coated

By: Ge

Part Number: WD28X20163

The coated tines is an OEM part for GE dishwashers. Acting as the separator between dishes and silverware, the tines are responsible for keeping cutlery in place during the wash cycle while allowing for full access of water and spinning.

Causes of badly coated tines can include corrosion or rusting over time due to wear and caustic chemicals, or damage and bending due to frequent loading or unloading of dishes.

Symptoms of badly coated tines include:

Cutlery clumping together instead of being properly separated
Tines broken, bent, or missing entirely
Poor wash performance due to inability to properly separate and distribute water

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.