Gdfe10pgj2bb Parts

This dishwasher feed tube channels wash water from the sump to the middle spray arm, restoring proper water delivery to help ensure thorough cleaning between racks.

• Directs pressurized water to the middle spray arm during wash cycles
• A worn, cracked, or leaking tube can reduce spray pressure and cleaning performance
• Common symptoms include poor wash results on the middle rack, weak spray, or visible leaks from the conduit area
• Replacing the conduit can resolve intermittent spray or uneven cleaning

• Disconnect power and water supply before servicing
• Remove lower rack and any fasteners/clips securing the conduit; note routing and orientation
• Inspect and transfer any reusable seals or clips only by the manufacturer
• After installation, run a short cycle to check for proper spray and leaks

This heater nut secures the dishwasher's heating element where it passes through the tub, helping maintain a tight connection and proper positioning. Replacing a damaged or missing nut can help prevent leaks and keep the element stable.

• Fastens the heating element to the tub from below to hold it firmly in place
• Helps support a watertight connection at the element pass-through when used with the proper seal
• Replace if the nut is cracked, heat-damaged, stripped, or missing
• Common symptoms include water leaking under the unit near the heater terminals and a loose or wobbly heating element

• Disconnect power at the breaker and shut off water before servicing
• Access the nut from beneath the dishwasher; remove the toe-kick and pull the unit forward if needed
• Support the element from inside the tub while tightening; snug gently and do not overtighten to avoid damage
• Restore power/water and run a short cycle to check for leaks

This pump isolator hanger secures and cushions the dishwasher's pump assembly, helping reduce vibration and noise while keeping the pump properly supported. Replacing a worn hanger restores stable, quieter operation and maintains correct pump alignment.

• Supports and isolates the pump assembly beneath the tub to dampen vibration
• Helps keep the pump properly positioned and prevents contact/rattling
• Replace if the hanger is stretched, cracked, or broken
• Common symptoms include louder operation, rattling from the base, or a sagging pump assembly

• Disconnect power and shut off water before servicing; wear gloves and eye protection
• Access from the front base by removing the toe-kick/kickplate; support the pump assembly
• Detach the worn hanger from its mounting points and install the new hanger in the same locations
• Ensure the pump is secure, hoses/wires aren't strained, and run a brief test for noise/vibration

This clip bracket attaches to the dishwasher rack to secure a rack-mounted component or accessory. Replace a cracked or missing bracket to keep parts firmly in place so the rack loads easily and performs as designed.

• Attaches to the rack to hold the mating part securely in place
• Helps prevent shifting, rattling, or accessories falling off during cycles
• Restores proper fit when the original clip is broken, worn, or missing
• Typical signs: accessory won't stay attached, clip is visibly cracked or missing, loose components during operation

• Disconnect power at the breaker and turn off the water supply
• Pull out the rack to access the clip location
• Release the old clip's locking tabs and remove; align and snap the new clip firmly in place
• Verify a secure fit before reinstalling the rack and running a test cycle

The Main Control Board is an OEM component specifically designed for GE dishwashers. It acts as the central "brain" that facilitates all washing functions. Integrated electronic components and programmed controls coordinate important operations like wash cycles, temps, dispensing, the user interface, and more. Over time electrical connections can degrade or surface mount chips fail.

Causes of a bad control board may arise from power surges, water exposure damage or simply normal component wear over thousands of wash cycles.

Symptoms of a failed control board include:

• The dishwasher failing to start or stopping mid-cycle
• Inability to change wash options or respond to button inputs
•  Strange electrical noises, smells, or error codes displayed

This genuine OEM GE part restores full operational capability with factory programming and reliability. It is also compatible with Hotpoint, RCA, and some Kenmore models for a direct replacement upgrade.

The White Toe Kick is an OEM component specifically designed for GE dishwashers. This toe kick forms the lower front panel of the dishwasher beneath the door. It is responsible for providing a finished look and protecting the inner components. 

The toe kick can become faded, cracked, or warped over time due to repeated cleaning. Improper cleaning methods may also damage the surface of the toe kick. 

Symptoms of a damaged toe kick include:

• Discoloration or fading of the white surface
• Cracks or chips in the paint/finish
• Warping that causes gaps around the door seal

This replacement part is also compatible with Profile, Hotpoint, RCA, and select Kenmore models.

Size: 10-32 GXTT FLP.595 S

This detergent cup cover attaches to the dishwasher's dispenser to seal the detergent compartment until the control releases it. Replacing a damaged cover prevents early washout and restores consistent detergent release for reliable cleaning results.

• Covers and seals the dispenser's detergent cup
• Opens at the proper time to release detergent into the wash
• Helps prevent detergent leaking or washing out too early
• Typical symptoms: cup won't stay closed, poor cleaning, visible damage to the cover/hinge

• Disconnect power to the dishwasher before servicing
• Handle hinge tabs carefully; transfer and tension the existing spring/pin if your model uses them
• After installation, close and manually release the cover to ensure smooth operation before running a cycle

Replace a worn or broken tub roller with this Tub Roller and Stud Assembly. It mounts to the dishwasher tub wall to guide the rack smoothly, preventing dragging, binding, or derailment when loading and unloading.

• Mounts on the tub sidewall to provide a smooth glide point for the dish rack
• Restores easy rack movement and can reduce squeaking or scraping noises
• Helps keep the rack aligned and prevents it from jumping off track
• Typical signs of failure: cracked/broken wheel, missing/bent stud, rack difficult to slide

• Disconnect power and water supply before servicing; wear cut-resistant gloves.
• Pull the rack out to access the roller location inside the tub.
• Remove the old roller and stud (retainer/tab/screw varies by model) and install the new assembly in the same orientation.
• Slide the rack in and out to confirm smooth movement before returning the appliance to service.

This replacement flood stem holds and guides the washer's water-level float so the machine can detect and control water levels. Replaces a worn or damaged mounting tube to restore reliable float operation. What it does:

• Secures and positions the water-level float inside the tub or housing
• Allows the float to move freely so the machine senses proper water level
• Helps prevent overfill and incorrect fill-level behavior when functioning correctly
• Common symptoms of a faulty unit: incorrect water level, washer overfills or fills unevenly, or the machine shows fill/drain issues

• One flood stem

• Disconnect power and turn off the water supply before starting any repair
• Replacement typically requires access to the washer cabinet/top or inner tub area
• Handle the float and tube gently to avoid damage; ensure proper seating and alignment during reassembly
• After installation, run a short fill/drain cycle to confirm correct float operation and that there are no leaks

The Rack Slide is an OEM replacement part for GE dishwashers. It refers to the components that allow the upper rack to glide smoothly in and out. Allowing for continuous movement over extended use, the slides can degrade, causing friction or binding that restricts access to dishes.

Symptoms of bad rack slides include:

• Difficulty fully extending or retracting the racks   
• Noisy operation accompanied by grinding or squeaking noises
• Racks that do not run smoothly and become stuck partially open

Causes of rack slides becoming bad are normal wear and tear from loading and unloading dishes over many years. Motion parts wear out more quickly than stationary components.

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This arm hinge assembly restores smooth, controlled movement of a hinged component in your dishwasher, helping maintain proper alignment and reliable operation. Replacing a worn or broken hinge can reduce binding, squeaks, and misalignment that affect performance. What it does:

• Provides the pivot point and support for a hinged assembly
• Maintains alignment to ensure correct engagement and sealing
• Helps ensure smooth opening/closing motion without binding
• Replaces a hinge arm that is cracked, bent, or worn
• Common signs: stiff or uneven movement, squeaking or popping noises, misalignment, or visible damage

• 1 arm hinge assembly

• Disconnect power and water before servicing
• Support the door or movable assembly to relieve tension while removing the hinge
• Note orientation and transfer any side-specific hardware from the original part
• After installation, check for smooth motion and proper alignment before restoring power and water

Arm hinge assembly is the pivoting hinge that supports and guides the appliance door, restoring smooth, stable opening and closing for proper alignment and operation. Replacing a worn hinge helps stop sagging, misalignment, and scraping noises. What it does:

• Supports the door pivot and maintains proper hinge alignment for smooth opening/closing.
• Helps the door latch and seal correctly by keeping the door level and aligned.
• Common symptoms: door hangs or sags, door won't close or latch, rubbing or scraping noises during movement.
• Replaces a bent, worn, or broken hinge arm to restore normal door operation.

• Disconnect power before starting any service.
• Use proper hand tools and support the door while removing/installing the hinge to avoid damage or injury.
• Align the hinge and operate the door several times before fully tightening fasteners; follow manufacturer torque/fastening guidance if available.

This user interface board mounts behind the dishwasher's control panel and contains the tactile push-button switches. Replacing a failed board restores responsive controls so you can reliably start cycles and select options at the panel. What it does:

• Houses the tactile push-button switch matrix for the control panel
• Registers button presses and communicates selections to the main control board
• Helps resolve symptoms like unresponsive or intermittent buttons, panel not responding, or inability to start a cycle
• Restores normal control-panel responsiveness when the original board has failed

• 1 user interface tactile switch circuit board

• Disconnect power at the breaker before servicing
• Open the door and remove inner-door/console fasteners to access the control area
• Handle the board by the edges and observe ESD precautions; transfer any reusable mounting hardware from the original
• Seat connectors and any ribbon cable fully and in the correct orientation; do not force pins

The Filter Adapter is an OEM component specifically designed for GE dishwashers. Located inside the dishwasher tub, it functions to strain out large food particles from water before it reaches the wash arms.  The adapter holds the removable wash/rinse filters in place during operation, functioning as an extension of the filtration system. 

Causes of a bad filter adapter can include cracks or breaks compromising its sealing surface, wear and tear deforming filter retention features over time, or buildup inhibiting functionality.

Symptoms of a bad filter adapter include:  

• Loose or falling out removable filters during washing  
• Bypassing of food particles around compromised seals
• Reduced lifespan of disposable filters placed in a faulty adapter
• Debris accumulation impacting spray arm performance

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This user-cleanable fine filter sits in the bottom of the dishwasher and traps small food particles so the wash water stays cleaner. Replacing a damaged or clogged filter helps maintain spray pressure and consistent cleaning results.

• Screens fine debris from the recirculating wash water
• Helps prevent grit and food from redepositing on dishes and glassware
• Supports proper water flow to the spray system and pump
• When clogged or damaged, may cause poor cleaning, gritty residue, odors, or unusual pump noise

• Disconnect power before servicing the appliance
• Open the door and remove the lower rack; unlock and lift out the old fine filter per your model's instructions
• Rinse the area, install the new filter, and lock it securely so it sits flat
• The lower spray arm spins freely before running a test cycle