Gdt530psdoss Parts

The Water Valve is an OEM part for GE dishwashers. It controls the flow of water into the dishwasher during the wash and rinse cycles.

You should replace the water valve if it becomes defective or worn out. Over time, mineral deposits can build up, or the internal components can fail, leading to improper water flow. This can affect the dishwasher's performance and water efficiency.

Symptoms of a bad water valve include:

• The dishwasher not filling with water
• Low water pressure during the cycle
• Leaking water from the valve area
• Dishes remaining dirty due to insufficient water

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Hinge Pulley is an OEM part for GE dishwashers. This part works with the door springs and cables to provide smooth and balanced movement. This pulley ensures that the door operates efficiently, making it easy to load and unload dishes.

Causes of a bad door hinge pulley can include wear and tear from regular use, accumulation of debris or grease, or damage from accidental impacts.  

Symptoms of a bad door hinge pulley include:

• The dishwasher door not staying open or closed properly
• Difficulty in opening or closing the door
• Unusual noises during door operation, such as squeaking or grinding
• The door feeling loose or unbalanced

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This diverter assembly kit controls the dishwasher's wash-water routing. It switches flow between spray arms for targeted cleaning. Replacing a failed diverter restores proper water distribution and helps recover normal wash performance.

• Directs wash water between lower and upper/middle spray arms as the cycle advances
• Works with the control to provide zone/alternating spray for efficient cleaning
• Failure can cause poor cleaning on one rack or water spraying from only one arm
• May produce repeated clicking/grinding from the sump area or extended cycles while indexing

• Disconnect power and shut off water supply before servicing; expect some residual water
• Access the diverter at the sump/pump area; follow your model's service procedures
• Ensure seals/O-rings are properly seated and parts are aligned before tightening
• Run a short test cycle to check for leaks and confirm both racks receive spray

This main wash pump kit restores strong water circulation to drive the spray arms for thorough cleaning. Replace if the existing pump is weak, noisy, or leaking to recover proper wash performance.

• Circulates wash water through the spray arms during wash and rinse cycles
• Maintains proper water flow for consistent cleaning results
• Common failure signs: poor cleaning or no spray action, loud humming or grinding from the base, or leaks around the pump area

• Disconnect power and turn off the water supply before servicing
• Access the pump from the bottom; remove the toe-kick and pull the unit as needed
• Expect residual water—use a towel or pan; note hose and wire positions
• Seat seals fully and secure clamps; run a short test cycle to check for leaks

This right-hand roller cover is the small retainer that locks a dishwasher rack roller onto its mount. Replacing a cracked or missing cover restores smooth, stable rack movement and helps prevent the roller from working loose during use.

• Secures the right-hand rack roller to its axle/mount
• Helps the rack slide smoothly and stay level
• Replaces covers that are cracked, worn, or missing
• Symptoms include: rack binding on one side, tilting/dropping, rattling, or a roller that pops off

• Disconnect power and shut off water before servicing
• Pull the rack forward and remove if needed to access the roller area
• Release the old cover's locking tabs; align and snap the new cover into place on the right-hand side
• Ensure the rack rolls smoothly and sits level; right- and left-hand pieces are not interchangeable

This dishwasher main control board kit is the central circuit board that directs all wash functions. Replacing a failed board restores proper power distribution and timing so cycles start, advance, and finish correctly, helping prevent intermittent shutdowns and erratic operation. What it does:

• Controls cycle timing and communicates with sensors
• Distributes power to the wash motor, drain pump, inlet valve, and heater
• Works with the door latch and user interface to start/stop the cycle
• Failure may cause no power/won't start, stalled cycles, blinking lights/error codes, or incorrect filling, draining, or heating

• One main control board kit

• Disconnect power at the circuit breaker; turn off water if moving the dishwasher for access
• Board is typically in a housing beneath the unit—use ESD precautions and keep connections dry
• Photograph/label wire harnesses; transfer connectors one at a time to the new board
• Restore power and run a test or rinse cycle to proper operation

This leveling leg adjusts the dishwasher's height at the base, helping you level and stabilize the unit inside the cabinet. Proper leveling reduces rocking and vibration and promotes a tight door seal and smooth rack operation.

• Screws into the base frame to set height and level the dishwasher
• Supports the unit to prevent rocking or wobbling
• Helps maintain door alignment and sealing; poor leveling can contribute to leaks
• A worn, bent, or missing leg can make leveling difficult and increase vibration/noise

• Disconnect power and shut off water; slide the dishwasher out if needed for access
• Turn the leg with a wrench or pliers to adjust height; replace by threading the new leg into the base
• Use a bubble level to set side-to-side and front-to-back level before re-securing the unit
• Do not overtighten; ensure both legs carry weight evenly on a solid floor surface

The Vent Filter is an OEM part for GE dishwashers. It helps to capture and filter out food particles, grease, and other debris. 

Causes of a bad vent filter can include clogging or blockage due to accumulated debris, wear and tear over time, or damage to the filter material.

Symptoms of a bad vent filter include:

• Lingering unpleasant odors during or after the dishwasher cycle
• Visible signs of debris or buildup on the filter surface
• Reduced effectiveness of the dishwasher's drying performance

Replace your worn-out or clogged vent filter with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Rack bracket with three wheels for the dishwasher rack. This assembly mounts to the rack and rides in the rail to keep the rack level and rolling smoothly, replacing cracked wheels or a damaged bracket to restore easy operation.

• Supports the rack and rolls along the rail on three wheels
• Restores smooth in-and-out rack movement
• Helps keep the rack aligned and prevents derailing or dropping
• Typical failure signs: cracked/broken wheels, damaged bracket, rack binding

• Disconnect power at the breaker; shut off water supply for safety
• Pull the rack out and remove any rail end caps/stops to access the bracket
• Release the old bracket and install the new one in the same orientation
• Reinstall stops, reseat the rack, and verify smooth travel

This dishwasher junction box cover encloses the power-connection compartment at the base of the unit. Replacing a damaged or missing cover helps protect wiring from debris and accidental contact, restoring a safe, secure connection area. What it does:

• Covers and secures the dishwasher's electrical junction box
• Helps shield wire splices from moisture, dust, and accidental contact
• Restores proper fit when the original cover is cracked, broken, or missing
• Useful if the junction box won't stay closed or the cover no longer secures properly

• Includes 1 junction box cover

• Disconnect power at the circuit breaker before servicing
• Remove the lower access/kick panel to reach the junction box
• Remove the old cover and screw, position the new cover, and secure with the existing hardware
• Ensure all wiring and the strain relief are fully inside the box before closing; restore power and test

This adapter plate is a molded interface in the wash system that secures and seals components so water pressure is routed correctly. Replacing a cracked or warped plate helps stop leaks and restore proper spray performance.

• Connects and supports wash-system components at the sump/water-feed interface
• Maintains a reliable seal to help prevent leaks
• Helps direct wash water to the spray arms for effective cleaning
• Replace if cracked, warped, or stripped; symptoms can include leaks, weak spray, or a loose spray arm

• Disconnect power and water supply before servicing
• Remove the lower rack and related wash components to access the plate; note the order of parts for reassembly
• Reuse existing seals and fasteners in their original positions; seat the plate evenly and tighten hardware snugly, not overtight
• Run a brief test cycle and inspect for leaks before full use

This conduit seal fits the dishwasher's water-feed conduit connection, keeping wash water contained and pressure steady to the spray arms. Replacing a worn seal helps address leaks and maintain reliable cleaning performance.

• Seals the joint where the dishwasher's water feed conduit/tube connects within the wash system
• Helps prevent water leaks at the conduit connection point
• Maintains proper wash pressure for consistent spray performance
• Common signs of failure: drips beneath the unit, visible cracks/flattening, or a loose-fitting old seal

• Disconnect power and shut off the water supply before servicing
• Access the conduit connection (location varies by model), remove the old seal, and clean mating surfaces
• Lightly moisten the new seal to ease installation and seat it fully
• Reassemble and run a brief cycle to check for leaks

This dishwasher turbidity sensor assembly monitors water clarity in the sump and reports to the control so it can adjust wash time and rinses for optimal cleaning. Replacing a failed sensor can restore normal cycle decisions and performance.

• Measures wash-water clarity (soil/turbidity) and sends data to the control
• Helps optimize cycle length, number of rinses, and water usage
• A faulty sensor may cause unusually long or short cycles
• Can contribute to poor cleaning or failure to complete a cycle
• May set a sensor-related code in diagnostics on some models

• Disconnect power at the breaker and shut off water before servicing
• Access from the bottom/front of the dishwasher; place a towel to catch residual water
• Unplug the wire connector, rotate the sensor to unlock, and remove; ensure the seal seats properly when installing the new part
• After installation, check for leaks and run a test cycle

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection