Gdt535psm0ss- Parts

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

This control box bottom is the lower housing piece that secures and protects the appliance control board and related components. It restores a stable mounting surface and helps keep electronics shielded from vibration and debris. What it does:

• Provides the lower half of the control box housing to support and protect the control board
• Keeps wiring and connectors routed and held in place to prevent strain
• Replaces cracked, broken or warped housing that can expose electronics
• Helps stop rattling or movement of the control assembly that can cause intermittent controls

• Control box bottom

• Power off and unplug the appliance before starting any repair
• Handle the control board and connectors carefully to avoid electrostatic or mechanical damage
• This part typically installs with screws or clips; retain fasteners and note their locations during disassembly
• Inspect and address the electronics before reassembly

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

Left side roller cover.

The User Interface Housing is an OEM replacement part for GE dishwashers. Located at the front of the console, it houses the control panel responsible for cycle/option navigation.

The housing protects sensitive electronic components from water damage and physical impact. Its sturdy construction allows for responsive touch inputs without flex or play in the assembly. 

Symptoms of a bad user interface housing include:

• Warping or cracks exposing circuitry to damage
• Faulty sealing allowing moisture penetration
• Difficulty registering button presses from structural defects
• Ill-fitting installation negatively impacting usability

Causes can be repetitive openings allowing entry of dirt/moisture into critical areas and use over the years breaking down seals and weakening materials.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This floor plate is the OEM-style replacement that fits under the oven cavity to protect internal components and provide a stable cooking surface. Restores proper support and helps maintain even heat distribution in the lower oven area. What it does

• Covers and protects the oven's lower cavity from spills, drips, and falling debris
• Helps funnel heat and airflow for more consistent baking and roasting performance
• Prevents direct contact between food/drips and heating components
• Reduces corrosion and wear to inner oven parts caused by spills

• One floor plate as shown

• Designed to be installed in the lower oven cavity; for exact placement
• Remove power (unplug or shut off breaker) and allow the oven to cool before servicing
• Use appropriate gloves to avoid sharp edges; avoid forcing the part into place

This latch cam engages the door latch mechanism so the appliance door closes and stays secure during cycles. A worn or broken cam can prevent the door from latching or cause the door to feel loose. What it does

• Rotates with the latch to lock the door securely during operation
• Ensures the latch striker catches and holds the door closed
• Common symptom: door won't stay latched or appliance won't start
• Common symptom: door feels loose, noisy, or intermittently opens during cycles

• One latch cam

• Disconnect power before starting any repair to avoid shock or injury
• Inspect surrounding latch components and replace any visibly damaged parts
• Use basic hand tools; keep track of small fasteners and alignment during reassembly
• Test door operation several times after installation to ensure secure engagement

This inner door assembly replaces a damaged or worn inner panel to restore a secure, insulated door interface and proper sealing. It fits into the existing door frame to help resolve door rattling, poor closure, or visible inner-door damage. What it does:

• Replaces the appliance's inner door panel to restore structural integrity and improve sealing.
• Helps stop door rattling, unusual vibration, or gaps caused by a cracked or bent inner door.
• Restores the inner surface that supports door hardware and seals.
• Enables proper alignment for the outer door and latch operation when the inner panel is the cause of failure.

• One inner door assembly

• Disconnect power to the appliance before starting any repair.
• Handle door components carefully—sharp edges or glass may be present.
• Basic tools (screwdriver, socket) typically required; follow service manual for disassembly/reassembly steps.

This high loop drain hose creates the required elevated drain loop to help prevent dishwasher backflow and ensure proper drainage. It replaces a worn or damaged drain loop and restores correct drain routing for reliable performance. What it does:

• Forms the high loop in the dishwasher drain line to reduce risk of sink water siphoning back into the appliance
• Directs wastewater from the dishwasher into the household drain properly
• Helps avoid intermittent draining issues caused by a collapsed or split drain loop
• Fits into existing drain connections—used where an elevated drain loop is required

• Designed for in-line replacement; route the hose to create a high loop secured under the countertop or cabinet as shown in the appliance installer instructions
• Turn off power and water supply to the appliance before performing service
• Inspect clamps and fittings and replace if corroded; ensure all connections are snug but not over-tightened

The Rack Roller is an OEM component compatible with GE dishwashers. Located on the rack guide rails inside the washer tub, it facilitates smooth gliding of rack shelving in and out for easy loading and unloading. 

Causes of failure can include cracked/warped rollers from years of continual movement, accumulation of debris preventing free motion, or detachment of roller heads compromising installation.

Symptoms include:

• Difficulty fully extending or retracting racks  
• Off-tracking of shelving from left to right rails
• Scratches or damage to dishware from improper rack functioning 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Clamp is an OEM replacement part for GE dishwashers. It holds and secures critical components such as tubing or hoses securely in place. Clamps play an important supporting role by fastening tubing and preventing kinking, both of which are essential for proper water flow and circulation within the dishwasher.

Causes of a bad clamp can include cracks, corrosion, or fatigue that causes the clamp to fail in its gripping function over time. Hoses or tubes may also wear down a clamp through constant vibration. 

Symptoms of a bad clamp include:

• Leaks from hoses, tubes or connections  
• Reduced water pressure or uneven spray patterns
• Moisture or water damage around connections
• Loose hoses that rub or chafe

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Float Mounting Tube O Ring is an OEM component specifically designed for GE dishwashers. This float mounting tube o-ring creates a watertight seal around a tube that helps monitor water levels using a float and switch assembly.  

Causes of a bad float mounting tube o-ring can include cracks, tears or warping that prevents proper sealing. Chemical exposure from regular dishwasher use can cause o-rings to degrade over time.

Symptoms of a bad Float Mounting Tube O Ring include:

• Water leaks in the area around the tube fitting  
• Moisture or water damage near water level monitoring components
• Irregular or improperly timed cycles from inaccurate water level readings
• Safety issues from undetected pooling or overflow of water

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This dishwasher hose clamp secures internal hoses to pumps or fittings, helping prevent leaks and disconnections. Replace a weakened or damaged clamp to restore a tight, reliable seal at the connection.

• Provides clamping pressure to hold a hose on pump, sump, or drain fittings
• Helps stop water leaking at hose joints
• Resolves: loose or disconnected hoses, water under the unit/base, or poor draining from a slipped drain hose
• Replaces worn, rusted, or deformed clamps after service

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher forward as needed for access; place a towel or pan to catch residual water
• Seat the hose fully, then compress or tighten the clamp per its design; position just behind the hose barb bead
• Run a short cycle and inspect for leaks at the connection

This AC harness assembly carries incoming line voltage through the dishwasher to the control and other components. Replacing a damaged or heat-stressed harness restores safe, reliable power distribution and can resolve dead controls, no-start, or intermittent power issues.

• Distributes AC power from the dishwasher's power connection to the control and key components
• Provides correct wire routing with factory-terminated connectors for a secure fit
• Replace if wires are cut or melted, or if terminals show heat damage or looseness
• Common symptoms: won't power up or start, dead controls, intermittent power loss

• Disconnect power at the circuit breaker before servicing; verify power is off
• Remove toe-kick and access panels to reach the harness; note original routing and clips
• Move one connector at a time to the new harness; seat fully without forcing and avoid pinching
• Use the model's wiring diagram to confirm connections; secure wiring and reinstall panels