Gdt550hsd0ss35psm0ss Parts

This console cover graphic is the labeled overlay that mounts on the appliance control console, restoring clear, readable control markings and the console's finished appearance for easier control use and improved cosmetics. What it does:

• Replaces faded, cracked, or peeling control labels so settings and icons are legible
• Restores the visible markings around buttons and knobs for accurate operation
• Covers and protects the underlying console surface from everyday wear
• Improves the appliance's appearance by replacing damaged or discolored graphics

• Disconnect power to the appliance before starting any repair
• Typically installs using the console's existing screws or clips; align carefully before fastening
• Handle the graphic by the edges to avoid fingerprints or damage to the printed surface
• After installation, restore power and verify all controls operate and labels align correctly

This gray dishwasher vent releases moist air from the tub during the dry cycle on hybrid-dry models. Replacing a damaged vent helps control steam and condensation for more consistent drying and a cleaner door area.

• Directs steam out of the tub during hybrid drying
• Helps reduce interior condensation for improved drying results
• If cracked, warped, or loose, you may notice steam escaping at the door, moisture on the console, or dishes that stay wet
• Visible damage or discoloration around the vent area can indicate replacement is needed

• Disconnect power at the circuit breaker before servicing
• Access is typically through the inner door panel; handle sharp edges and note original orientation
• Ensure the vent seats evenly and fasteners are secure without overtightening
• Run a short cycle and check for proper venting/steam control after reassembly

Size: 8-16 x 2 inch ss.

Restore your appliance's factory look with this badge assembly. It replaces a missing, cracked, or faded logo on the refrigerator exterior, delivering a clean, professional appearance without affecting performance or operation.

• Decorative nameplate/logo for the refrigerator exterior
• Replaces cracked, faded, loose, or missing badge
• Restores a clean, factory appearance
• Cosmetic component; does not impact cooling or function

• Disconnect power before servicing the appliance
• Protect the finish; use a plastic trim tool to remove the old emblem if needed
• Clean and dry the mounting area; align with locating marks/holes and secure per your model diagram

Size: 10-16 ab.

This rack clip is a small fastener used on GE dishwashers to secure components on the dishrack, such as adjustable tines or accessory holders. Replacing a damaged clip helps keep the rack stable and prevents parts from shifting during cycles.

• Secures rack components and attachments in position
• Helps adjustable tines or holders stay locked during loading and wash
• Replaces cracked, loose, or missing clips
• May correct issues like wobbly rack sections, parts falling off, or rattling noises

• Unplug the dishwasher or switch off the circuit breaker before servicing
• Pull the rack out for access
• Release the old clip (press/squeeze tabs), align the new clip, and snap it fully into place
• Verify the rack and attachments move smoothly and lock securely

This insulation toe kick is a replacement panel that fits the refrigerator base to help block drafts and protect internal components under the cabinet. It restores the factory barrier that supports temperature stability and efficient operation. What it does

• Replaces damaged or missing toe-kick insulation that lets cold air escape beneath the appliance
• Helps reduce drafts and minimize warm air intrusion into the refrigerator cavity
• Protects wiring and components located in the toe-kick area from dust and debris
• Can help prevent uneven cooling or frost buildup that results from compromised base insulation

• One insulation toe kick panel

• Disconnect power to the appliance before starting any service
• Remove the existing toe kick/board and fasteners, then position the replacement so mounting tabs align with factory slots
• Avoid compressing or tearing the insulation; maintain original fit for proper performance

This replacement vent restores proper air flow for non-fan appliance models, helping exhaust heat and cooking odors while protecting internal components from debris. A direct-fit OEM-style vent for units that do not use a powered blower. What it does:

• Channels exhaust air and heat away from the appliance to maintain safe operating temperatures
• Helps prevent buildup of debris and grease in the vent opening
• Can reduce intermittent overheating and cooking odors caused by a damaged or missing vent
• Restores proper fit and appearance at the appliance vent outlet

• One replacement vent

• Disconnect power to the appliance before beginning any service
• Access may require removing the lower kick panel or outer cover
• Use basic hand tools; align clips or screw holes and avoid forcing the part into place

Size: 8-32 t. Includes 12 screws.

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

Left side roller cover.

A white plastic tub trim that restores the washer's front appearance and helps seal the gap between the outer cabinet and inner tub. Replaces worn or cracked trim to improve fit and finish. What it does:

• Covers and protects the tub edge, providing a finished look around the washer opening
• Helps maintain a snug seal between the tub and cabinet trim to reduce snagging and debris buildup
• Common replacement for cracked, warped, or discolored trim that affects appearance or clearance
• Matches factory finish and mounting locations for a correct, secure fit

• One tub trim (white)

• Turn off and unplug the appliance before beginning any repair
• Removal typically requires opening the access panel or unhooking clips; handle trim gently to avoid snapping mounting tabs
• Keep mounting hardware and clips; reuse if undamaged or replace with manufacturer parts

This latch cam engages the door latch mechanism so the appliance door closes and stays secure during cycles. A worn or broken cam can prevent the door from latching or cause the door to feel loose. What it does

• Rotates with the latch to lock the door securely during operation
• Ensures the latch striker catches and holds the door closed
• Common symptom: door won't stay latched or appliance won't start
• Common symptom: door feels loose, noisy, or intermittently opens during cycles

• One latch cam

• Disconnect power before starting any repair to avoid shock or injury
• Inspect surrounding latch components and replace any visibly damaged parts
• Use basic hand tools; keep track of small fasteners and alignment during reassembly
• Test door operation several times after installation to ensure secure engagement