Gdt55ohsd6ss Parts

This heater nut secures the dishwasher's heating element where it passes through the tub, helping maintain a tight connection and proper positioning. Replacing a damaged or missing nut can help prevent leaks and keep the element stable.

• Fastens the heating element to the tub from below to hold it firmly in place
• Helps support a watertight connection at the element pass-through when used with the proper seal
• Replace if the nut is cracked, heat-damaged, stripped, or missing
• Common symptoms include water leaking under the unit near the heater terminals and a loose or wobbly heating element

• Disconnect power at the breaker and shut off water before servicing
• Access the nut from beneath the dishwasher; remove the toe-kick and pull the unit forward if needed
• Support the element from inside the tub while tightening; snug gently and do not overtighten to avoid damage
• Restore power/water and run a short cycle to check for leaks

The White Toe Kick is an OEM component specifically designed for GE dishwashers. This toe kick forms the lower front panel of the dishwasher beneath the door. It is responsible for providing a finished look and protecting the inner components. 

The toe kick can become faded, cracked, or warped over time due to repeated cleaning. Improper cleaning methods may also damage the surface of the toe kick. 

Symptoms of a damaged toe kick include:

• Discoloration or fading of the white surface
• Cracks or chips in the paint/finish
• Warping that causes gaps around the door seal

This replacement part is also compatible with Profile, Hotpoint, RCA, and select Kenmore models.

This left-hand rack slide end cap restores the stop at the end of your dishwasher's rack rail. It keeps the rack secured on the slide and ensures controlled travel when the original cap is broken or missing.

• Snaps onto the left rack slide/rail to act as a retention stop
• Helps keep the rack aligned and prevents it from pulling completely out
• Typical symptoms: rack slides out too far, falls off the rail, or the end cap is broken/missing
• Maintains proper rack retention to reduce spills and track damage

• Disconnect power and shut off water before service
• Pull the rack forward to access the end of the left slide rail (left side when facing the dishwasher)
• Release the locking tab to remove the old cap; align and push the new cap onto the rail until it clicks
• Slide the rack in and out to confirm smooth travel and a positive stop

This clip bracket attaches to the dishwasher rack to secure a rack-mounted component or accessory. Replace a cracked or missing bracket to keep parts firmly in place so the rack loads easily and performs as designed.

• Attaches to the rack to hold the mating part securely in place
• Helps prevent shifting, rattling, or accessories falling off during cycles
• Restores proper fit when the original clip is broken, worn, or missing
• Typical signs: accessory won't stay attached, clip is visibly cracked or missing, loose components during operation

• Disconnect power at the breaker and turn off the water supply
• Pull out the rack to access the clip location
• Release the old clip's locking tabs and remove; align and snap the new clip firmly in place
• Verify a secure fit before reinstalling the rack and running a test cycle

This top-control console is the panel at the upper edge of the dishwasher door. It forms the interface area for selecting cycles and protects the components behind it, helping keep the controls aligned and presentable.

• Houses and protects the user interface at the top edge of the door
• Provides the interface area for cycle and option selection
• Restores fit and appearance when the original console is cracked, warped, or loose
• Help if buttons feel misaligned due to a damaged console housing

• Disconnect power at the breaker before servicing; shut off water if moving the appliance.
• Open the door and remove perimeter screws to separate inner/outer door panels; support wiring when removing the console.
• Transfer any model-specific components from the original console to the new console; avoid pinching harnesses during reassembly.
• Restore power and selections engage and the door latches properly.

Size: 10-32 GXTT FLP.595 S

This detergent cup cover attaches to the dishwasher's dispenser to seal the detergent compartment until the control releases it. Replacing a damaged cover prevents early washout and restores consistent detergent release for reliable cleaning results.

• Covers and seals the dispenser's detergent cup
• Opens at the proper time to release detergent into the wash
• Helps prevent detergent leaking or washing out too early
• Typical symptoms: cup won't stay closed, poor cleaning, visible damage to the cover/hinge

• Disconnect power to the dishwasher before servicing
• Handle hinge tabs carefully; transfer and tension the existing spring/pin if your model uses them
• After installation, close and manually release the cover to ensure smooth operation before running a cycle

The Rack Slide is an OEM replacement part for GE dishwashers. It refers to the components that allow the upper rack to glide smoothly in and out. Allowing for continuous movement over extended use, the slides can degrade, causing friction or binding that restricts access to dishes.

Symptoms of bad rack slides include:

• Difficulty fully extending or retracting the racks   
• Noisy operation accompanied by grinding or squeaking noises
• Racks that do not run smoothly and become stuck partially open

Causes of rack slides becoming bad are normal wear and tear from loading and unloading dishes over many years. Motion parts wear out more quickly than stationary components.

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

Replace a worn or broken tub roller with this Tub Roller and Stud Assembly. It mounts to the dishwasher tub wall to guide the rack smoothly, preventing dragging, binding, or derailment when loading and unloading.

• Mounts on the tub sidewall to provide a smooth glide point for the dish rack
• Restores easy rack movement and can reduce squeaking or scraping noises
• Helps keep the rack aligned and prevents it from jumping off track
• Typical signs of failure: cracked/broken wheel, missing/bent stud, rack difficult to slide

• Disconnect power and water supply before servicing; wear cut-resistant gloves.
• Pull the rack out to access the roller location inside the tub.
• Remove the old roller and stud (retainer/tab/screw varies by model) and install the new assembly in the same orientation.
• Slide the rack in and out to confirm smooth movement before returning the appliance to service.

The Console Cover is an OEM replacement part for GE dishwashers. It provides an important protective covering for the control panel interface where users select cycle options and monitor the machine's status. 

Symptoms of a bad console cover include:

• Cracks, chips, or other exterior damage affecting the cover's integrity 
• Buttons or displays no longer functioning properly due to internal issues beneath the cover
• Looseness, sagging, or missing mounting screws causing it to fall off unexpectedly

Over extended use, the plastic materials used for console covers can become worn and degraded through typical wear and tear. Replacing with this genuine GE part ensures the control area remains fully enclosed and protected against water intrusion or other problems. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models. 

Restore proper wash performance with this turbidity sensor. It reads the clarity of the wash water so the control can adjust cycle length, fills, and rinses automatically for efficient, consistent cleaning. What it does:

• Monitors water clarity/soil level via an optical sensor in the sump
• Sends data to the control to optimize wash time, rinses, and water use
• Failure can cause unusually long or short cycles or failure to advance
• Contribute to poor cleaning results or repeated fills/drains

• 1 turbidity sensor

• Disconnect power and shut off water supply before servicing
• Access the sensor from the bottom/front of the tub at the sump area; removing the toe-kick or pulling the unit forward may help
• Release the locking tab/twist-lock, unplug the connector, and transfer the existing seal if needed
• Seat the new sensor fully, reconnect wiring, restore utilities, and run a short cycle to check for leaks and normal operation

This drain hose elbow creates a secure 90-degree connection in the dishwasher's drain line, helping route the hose cleanly while maintaining good flow. It supports a tight, leak-resistant turn where space is limited, reducing kinks and misrouting.

• Provides a 90-degree turn for the dishwasher drain hose to aid proper routing and flow
• Helps reduce kinks or crushing at tight bends that can slow or stop draining
• Forms a secure connection point to help prevent leaks at the hose junction
• Common symptoms of a failed or damaged elbow include leaks under the sink, visible cracks, kinks, or slow/poor draining

• Disconnect power and water supply; place a towel or pan to catch residual water
• Ensure the hose is fully seated on the elbow and secured with appropriate clamps per your model
• Route the drain line with a high loop or air gap as required by local code
• Run a short cycle and check all connections for leaks

This console cover and graphics assembly is the outer control-panel fascia for your dishwasher. It refreshes the appearance, keeps cycle labels clear, and helps protect the user interface area from everyday wear.

• Provides the front console surface with printed cycle and option graphics
• Shields underlying controls from moisture and routine use
• Helps keep the control area aligned, stable, and easy to clean
• Common signs of failure: cracked or broken panel, peeling/bubbled overlay, faded or illegible labels, loose or rattling console

• Disconnect power at the breaker before servicing; allow the door to cool and dry
• Open the door and remove inner-door/console screws to release the console
• Transfer any brackets, buttons, and hardware from the original console as needed
• Reassemble carefully and tighten screws evenly; restore power and test all controls

This twist-lock clip secures the dishwasher's heating element to the tub floor, keeping it properly positioned for effective water heating and drying. Replacing a broken or missing clip stops rattles and keeps the element stable during cycles.

• Locks the heating element to the tub/base with a twist-to-secure design
• Maintains correct element alignment and clearance
• Helps reduce rattling or scraping noises from a loose element
• Common signs: element sagging or out of place, broken/missing clip, poor drying results

• Disconnect power at the breaker and allow the heating element to cool before servicing
• Remove the lower rack to access the clip on the tub floor
• Rotate the old clip to release; position the new clip over the mounting slot and twist to lock
• Ensure the element is fully seated in the clip and not contacting the tub or spray arm

This console cover graphic is the labeled overlay that mounts on the appliance control console, restoring clear, readable control markings and the console's finished appearance for easier control use and improved cosmetics. What it does:

• Replaces faded, cracked, or peeling control labels so settings and icons are legible
• Restores the visible markings around buttons and knobs for accurate operation
• Covers and protects the underlying console surface from everyday wear
• Improves the appliance's appearance by replacing damaged or discolored graphics

• Disconnect power to the appliance before starting any repair
• Typically installs using the console's existing screws or clips; align carefully before fastening
• Handle the graphic by the edges to avoid fingerprints or damage to the printed surface
• After installation, restore power and verify all controls operate and labels align correctly

The Door Handle is an OEM part for GE dishwashers. It is designed to provide a secure grip and easy access for opening and closing the dishwasher door.

A bad Door Handle can result in issues such as difficulty in opening or closing the dishwasher door, or even complete failure to operate. Causes of a bad door handle can include wear and tear over time, accidental impacts that cause damage or breakage, or improper installation.

Symptoms of a bad Door Handle include:

• Difficulty in opening or closing the dishwasher door
• Loose or wobbly handle that fails to provide a secure grip
• Complete failure to open or close the dishwasher door
• Visible damage to the handle

Replace your worn-out or damaged Door Handle with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.