Gdt655mj2es Parts

The Vent Filter is an OEM part for GE dishwashers. It helps to capture and filter out food particles, grease, and other debris. 

Causes of a bad vent filter can include clogging or blockage due to accumulated debris, wear and tear over time, or damage to the filter material.

Symptoms of a bad vent filter include:

• Lingering unpleasant odors during or after the dishwasher cycle
• Visible signs of debris or buildup on the filter surface
• Reduced effectiveness of the dishwasher's drying performance

Replace your worn-out or clogged vent filter with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This tub insulation is the replacement foam/fiber wrap that lines the dryer drum area to help retain heat, reduce exterior cabinet temperature, and dampen operation noise for more efficient, quieter drying. What it does:

• Wraps around the dryer drum/tub to help limit heat loss during cycles
• Helps reduce cabinet surface temperature for safer operation
• Dampens vibration and operating noise from the rotating drum
• Supports consistent drying performance by improving heat retention
• Useful when original insulation is damaged, torn, or missing

• Disconnect power (and gas supply for gas dryers) before servicing
• Access requires removing the dryer cabinet or drum per OEM instructions
• Handle carefully—use gloves and eye protection; avoid breathing any loose fibers
• Reinstall with original fasteners and seal as needed to maintain drum clearance

This dishwasher junction box cover encloses the power-connection compartment at the base of the unit. Replacing a damaged or missing cover helps protect wiring from debris and accidental contact, restoring a safe, secure connection area. What it does:

• Covers and secures the dishwasher's electrical junction box
• Helps shield wire splices from moisture, dust, and accidental contact
• Restores proper fit when the original cover is cracked, broken, or missing
• Useful if the junction box won't stay closed or the cover no longer secures properly

• Includes 1 junction box cover

• Disconnect power at the circuit breaker before servicing
• Remove the lower access/kick panel to reach the junction box
• Remove the old cover and screw, position the new cover, and secure with the existing hardware
• Ensure all wiring and the strain relief are fully inside the box before closing; restore power and test

This dishwasher fill hose routes incoming water from the inlet valve into the tub. Replacing a brittle or leaking hose helps restore proper filling and reduces the risk of water leaks under the unit.

• Carries fresh water from the inlet valve to the dishwasher during the fill cycle
• Helps maintain correct water level for reliable wash performance
• Common symptoms of a failed hose: leaks near the toe kick, slow fill, or no fill
• Replaces hoses that are cracked, swollen, kinked, or deteriorated

• Disconnect power and shut off the water supply before service
• Place a towel or shallow pan to catch residual water
• Access behind the lower kick panel; transfer existing clamps/fittings as needed
• Route the hose without kinks, fully seat connections, restore water, and check for leaks during a test cycle

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

This Insulation Bag Assembly is an OEM part for GE dishwashers. It's designed to provide sound insulation and heat retention, enhancing the overall efficiency and noise reduction of the dishwasher. The insulation bag plays a vital role in maintaining the optimal operating temperature within the dishwasher while minimizing the sound during its operation. 

Replacement of the insulation bag assembly may be necessary due to wear, damage, or inefficiency in sound dampening or heat retention. A compromised insulation bag can lead to increased noise levels and reduced energy efficiency.

Symptoms of a malfunctioning Insulation Bag Assembly include:

• Noticeably louder operation of the dishwasher.
• The outer surfaces of the dishwasher becomes unusually warm during operation.
• Physical damage or wear to the insulation material.
• Changes in the dishwasher's drying performance due to altered internal temperatures.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This upper wash impeller circulates water to the upper spray system during the wash cycle, helping deliver thorough cleaning across dishes on the upper rack and throughout the tub.

• Drives water flow to the upper spray arm/manifold
• Worn or damaged impeller can cause weak spray, poor cleaning, or longer cycle times
• Physical damage (warping, cracks, stripped splines) warrants replacement

• Disconnect power and water before servicing
• Access is typically through the sump/pump area; note impeller orientation during removal
• Inspect mating parts (seal, hub, shaft/splines) and replace if worn
• Hand-tighten fasteners to OEM guidance and verify free rotation before reassembly

Size: 8-18 AB TSQ 5/8 SS

The AC Harness Assembly is an OEM replacement part for GE dishwashers. It is responsible for connecting the dishwasher's electrical system to the power source, ensuring proper functioning and power supply. This part provides a reliable and secure connection between the dishwasher and the electrical outlet. It is designed to deliver consistent and safe power during operation.

Symptoms of a faulty AC harness assembly include:

• Intermittent power loss
• Electrical shorts or sparks
• Dishwasher not turning on or receiving power

A bad AC harness assembly can occur due to wear and tear over time, loose or damaged wiring, or electrical malfunctions. If you experience issues such as intermittent power loss, electrical shorts, or the dishwasher not turning on, it may be time to replace the old or damaged AC harness assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

This replacement flood stem holds and guides the washer's water-level float so the machine can detect and control water levels. Replaces a worn or damaged mounting tube to restore reliable float operation. What it does:

• Secures and positions the water-level float inside the tub or housing
• Allows the float to move freely so the machine senses proper water level
• Helps prevent overfill and incorrect fill-level behavior when functioning correctly
• Common symptoms of a faulty unit: incorrect water level, washer overfills or fills unevenly, or the machine shows fill/drain issues

• One flood stem

• Disconnect power and turn off the water supply before starting any repair
• Replacement typically requires access to the washer cabinet/top or inner tub area
• Handle the float and tube gently to avoid damage; ensure proper seating and alignment during reassembly
• After installation, run a short fill/drain cycle to confirm correct float operation and that there are no leaks

The Filter Adapter is an OEM component specifically designed for GE dishwashers. Located inside the dishwasher tub, it functions to strain out large food particles from water before it reaches the wash arms.  The adapter holds the removable wash/rinse filters in place during operation, functioning as an extension of the filtration system. 

Causes of a bad filter adapter can include cracks or breaks compromising its sealing surface, wear and tear deforming filter retention features over time, or buildup inhibiting functionality.

Symptoms of a bad filter adapter include:  

• Loose or falling out removable filters during washing  
• Bypassing of food particles around compromised seals
• Reduced lifespan of disposable filters placed in a faulty adapter
• Debris accumulation impacting spray arm performance

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Conduit Main Assembly is an OEM replacement part for GE dishwashers. It is installed within the dishwasher tub below the upper wash arm, and is responsible for securely mounting and holding the upper wash arm in place during operation.  

Causes of a bad upper wash arm support include:

• Symptoms of a bad upper wash arm support include: 
• Vibration or noise from an unsecured wash arm
• Improper alignment of spray pattern
• Restricted rotation of the wash arm during washing  
• Leaks at the tub connection point

Symptoms can include cracks or breaks that compromise its structure, or wear over extended use without replacement.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This bottle blaster assembly supplies targeted wash water to the dishwasher's Bottle Jets to clean tall, narrow items like baby and sports bottles. Replace a damaged or clogged assembly to restore focused spray and top-rack cleaning performance. What it does:

• Routes wash water to the bottle jet nozzles for concentrated cleaning inside bottles and narrow openings
• Helps improve cleaning on items positioned over the Bottle Jets
• Failure symptoms include no spray from the bottle jets, poor upper-rack cleaning, leaks near the jet area, or visible cracks/damage

• 1 bottle blaster assembly

• Disconnect power and shut off water to the dishwasher before servicing
• Access the bottle jet area; release retaining clips/fasteners and note hose routing and connection points
• Transfer any reusable clips or seals from the original assembly if needed
• Fully seat connections; run a short cycle to check for leaks and proper jet spray

This is a 6-20 machine screw, 3/8 inch length, used to secure trim, panels, or small components on compatible cooking appliances. Replacing a missing or damaged screw helps keep parts tight and prevents rattles or shifting during use.

• Fastens brackets, panels, or trim in the appliance chassis
• Helps restore a secure fit when the original screw is stripped or lost
• Can resolve issues like loose trim, minor rattling, or misaligned panels
• Nickel finish for corrosion resistance in warm, humid environments

• Disconnect power and allow appliance to cool before servicing
• Remove only the necessary adjacent fasteners to access the mounting point
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Replace any missing clips or spacers originally used with the screw