Ge Cgs990setss Parts

This broil element is the oven's upper heating element that produces the direct, high heat used for broiling and browning. Replacing a faulty element restores proper broil performance and even browning on foods. What it does:

• Heats from the top of the oven to brown and broil food
• Supplies concentrated, high-temperature heat for searing and finishing dishes
• Common symptom: oven broil does not heat or produces little to no heat
• Common symptom: food browns unevenly or element shows visible damage or breaks

• Disconnect power to the appliance at the breaker or unplug before servicing
• Access typically requires removing the oven inner panel or broil cover; retain mounting screws
• Handle the element carefully to avoid bending or damaging terminals

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Fix burners that won't light, stay lit, or shut off completely with this gas control valve. Regulates flow to a single burner for steady flames and safe cooking.

Secures the cooktop to the range frame. Replace this bracket if it's bent, broken, or missing to restore proper alignment and eliminate rattling.

Factory screw secures brackets, panels, trim, or burner components on ranges, cooktops, and wall ovens. Replaces missing, stripped, or corroded fasteners.

This speed nut is a clip-on fastener that provides threads for a screw on the appliance. It secures sheet-metal panels, brackets, or trim and helps keep assemblies tight under vibration and repeated use.

• Provides captive threads so a screw can tighten into thin sheet metal
• Helps secure panels, brackets, and trim pieces in place
• Replace if a screw spins without tightening, a panel rattles/feels loose, or the original clip is missing or damaged
• Restores a snug, reliable attachment point without a loose nut

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool before servicing
• Note the clip's orientation; slide it onto the panel edge or stud as designed
• Start the screw by hand to avoid cross-threading; do not overtighten
• Wear cut-resistant gloves when handling sheet-metal parts

Secures the thermostat sensing bulb to the oven cavity wall for accurate temperature control. Replace if missing or damaged to prevent sagging bulb.

Fixes weak or uneven flames on LP gas ranges. This orifice spud meters propane flow to the burner. Easy DIY install restores proper flame size.

Fix improper flames or weak ignition on your range burner with this LP orifice spud. Meters propane flow for correct flame size and safe operation.

Delivers gas from the manifold to your range's top burner for reliable ignition and even flame. Replace when burners fail to light or heat unevenly. Verify fit with your model number.

Fix burner ignition issues with this electrode retaining clip. Secures the spark electrode to restore proper alignment and reliable lighting on your cooktop.

Decorative badge emblem that mounts on range control panel or door. Restores appliance exterior appearance when original is faded, scratched, or missing.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Replacement control knob assembly for range or stove. Installs on control panel to operate burners or oven settings. Needed when original is cracked, broken, faded, loose, or missing.