Ge Cgs990setss Parts

A bimetal limit switch that helps detect and control excessive oven or range temperature to protect heating elements and electronics. Replaces a failed temperature limiter to restore safe temperature regulation and oven shutoff behavior. What it does:

• Acts as a temperature-sensitive cutoff that opens when internal oven temperature exceeds safe limits.
• Helps prevent overheating by interrupting power to heating elements or control circuits.
• Commonly linked to symptoms such as oven not heating, oven shutting off unexpectedly, or continuous heat control failures.
• Works as a safety device; it does not provide normal temperature measurement for user temperature readouts.

• One bimetal limit switch.

• High-level replacement; disconnect power at the breaker before accessing internal oven parts.
• Handle terminals carefully and note wire locations or take a photo before removal for correct reassembly.
• Replace only if the device is confirmed faulty.

A 90° elbow assembly that redirects a fluid or discharge line at a right angle to restore proper routing and a secure connection. Simple replacement for worn, cracked, or damaged elbow fittings. What it does

• Redirects flow between two hoses or fittings at a 90° angle to enable correct line routing
• Provides a sealed connection to help prevent leaks where a straight connection won't fit
• Restores proper flow path to eliminate kinks or pressure loss caused by a damaged elbow
• Common symptom: visible leak, moisture or pooling near the elbow fitting
• Common symptom: poor or restricted flow where the line changes direction

• One 90° elbow assembly

• Turn off power and shut off the appliance water supply before starting any repair
• Inspect mating hoses and seals; replace worn clamps or gaskets for a reliable seal
• Hand-tighten then snug fittings; avoid over-tightening plastic fittings to prevent cracking
• After installation, restore water/power and check thoroughly for leaks during a test run

This oven deflector is a metal shield that directs heat away from sensitive areas inside the oven cavity to help ensure even cooking and protect surrounding components. It restores proper airflow and helps prevent hot spots. What it does:

• Directs and deflects oven heat to promote more even temperature distribution
• Protects internal components and wiring from direct heat exposure
• Helps reduce localized overheating that can cause oven damage or uneven baking
• Replaces a worn, bent, or missing deflector to restore original airflow path

• One oven deflector

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Typical install requires basic hand tools; follow the manufacturer service instructions
• Handle the part carefully to avoid sharp edges; wear gloves if needed

This panel manifold routes gas from the oven/range supply to the burner valves for consistent fuel delivery and reliable burner operation. Replaces a damaged or corroded manifold to help restore normal ignition and flame performance. What it does

• Distributes gas to individual burner valves so burners light and run properly.
• Keeps gas flow stable to prevent weak or uneven flames.
• A damaged or leaking manifold can cause burners not to light or a noticeable gas odor.
• Works with the range's control valves and burners to maintain safe operation.

• Turn off the gas supply and electrical power before servicing.
• Inspect nearby fittings and gaskets; replace any worn seals to ensure a gas-tight connection.
• Tighten fittings to manufacturer specs and test all connections with a leak-safe method (soapy water or approved detector).

This support base replaces the left lower support used to stabilize and align the appliance's lower assembly, restoring proper fit and reducing vibration. It helps keep moving parts supported during normal operation. What it does

• Provides structural support for the appliance's lower assembly and related components.
• Restores proper alignment to reduce rubbing, vibration, or uneven movement.
• Helps prevent excessive wear on brackets, panels, and adjacent parts.
• Safe, commonly used when the left support is cracked, broken, or warped.

• Disconnect power (and gas, if applicable) before beginning any repairs.
• Handle sharp sheet-metal edges and wear gloves and eye protection.
• Require basic hand tools to remove panels and fasteners; keep hardware for re-use if undamaged.
• If other mounting hardware or adjacent parts are damaged, inspect and replace as needed for secure installation.

This support base secures and stabilizes the appliance cabinet/frame so doors and components align properly and operate smoothly. Replaces worn or broken right-side lower support to restore correct support and fit. What it does:

• Provides structural support for the appliance cabinet/frame on the right side
• Helps maintain proper door alignment and prevent sagging or uneven gaps
• Reduces vibration and rattling related to a compromised support
• Restores correct mounting for adjacent components or trim

• Disconnect power and empty doors/drawers before starting any repair
• Remove relevant trim or access panels to reach the support; keep fasteners for reuse
• Replace using the original mounting locations; do not force or bend surrounding panels

This spacer base positions and supports components inside the appliance to maintain correct alignment and clearance, helping reduce vibration and wear. It's a simple replacement part when the original is cracked, broken, or missing. What it does:

• Provides a stable mounting surface and correct spacing for internal panels or components
• Restores proper alignment to reduce vibration, noise, and uneven operation
• Commonly replaced when the original spacer is cracked, deformed, or missing
• Helps maintain secure fastener engagement and proper component clearance

• Spacer base (single piece)

• Disconnect power to the appliance before starting any repair
• Follow manufacturer service instructions or parts diagram for correct location and orientation
• Basic hand tools typically required; inspect surrounding fasteners and mounting surfaces during installation

This bake burner is the oven's heat source for baking cycles, replacing a worn or damaged burner to restore consistent bake performance and even cooking results. Designed to match OEM fit and function. What it does:

• Provides the main heat for the oven's bake mode so food cooks through and browns properly
• Helps maintain even temperature distribution across the oven cavity
• Common replacement for symptoms like weak or no bake heat, uneven baking, or burner that won't ignite reliably
• Works with the oven's ignition and gas supply to deliver steady flame when functioning correctly

• Turn off power and shut off the gas supply before starting any repair
• Follow OEM service instructions; verify correct burner alignment and secure mounting before restoring gas and power
• Use caution handling sharp edges and hot surfaces; allow the appliance to fully cool before servicing

The Switch Harness is an OEM part for GE gas ranges. It connects various control interfaces like knobs, buttons and displays to the appliance's systems module. 

Causes of failure involve wiring cracking from repeated flexing at connection points throughout years of use, pinched bundles restricting consistent conductivity, and typical insulation degradation over extended heat exposure.

Symptoms of a faulty harness include:

• Burners or oven failing to ignite or operate as selected
• Inability to accurately set temperature or function controls  
• Intermittent or unstable power to surfaces and components

This OEM part is also compatible with Hotpoint and RCA models.