Ge Dcvh480ek0ww Parts

This SCR cover-back is a replacement cover that protects the appliance's SCR module and wiring, helping prevent contact damage and debris buildup for reliable operation. It restores the original protective shielding. What it does

• Protects the SCR module, control board area, and wiring from physical damage and dirt
• Helps reduce risk of electrical shorting from loose debris or accidental contact
• Maintains factory routing and placement of components behind the control area
• Restores the appliance's original protective enclosure after service

• One SCR cover-back replacement panel

• Designed to fasten using the original screws or mounting hardware; all retained hardware is present
• Disconnect power before servicing to avoid shock or damage to electronic components
• Handle with care to avoid bending mounting tabs; align tabs before tightening screws
• If control boards or modules were removed for access, recheck connections before reapplying power

This rubber mounting pad cushions and isolates appliance components to reduce vibration and noise, helping parts sit securely and run quieter. A simple replacement for worn or damaged pads that lets the appliance operate more smoothly. What it does:

• Acts as a vibration damper to reduce noise and movement during operation
• Provides a stable cushion between metal parts or between appliance and mounting surface
• Helps prevent rubbing, rattling or premature wear caused by metal-on-metal contact
• Commonly replaced when pads are cracked, compressed, missing or deteriorated

• Disconnect power and, if applicable, water supply before accessing internal components
• Inspect mounting area and clean surfaces before installing the new pad
• Press or fit the pad into place; no special tools typically required
• If multiple pads on the same assembly are worn, replace them together for even support

This handle tapping screw secures an appliance's handle to its door or front panel. Replacing a missing or stripped screw restores a firm, safe grip and prevents a loose or rattling handle. What it does:

• Fastens the handle to the door or front panel
• Self-tapping design engages/cuts threads for a secure hold
• Replaces missing, rusted, or stripped handle screws
• Helps correct a loose, wobbly, or rattling handle

• One handle tapping screw

• Disconnect power before service; for gas ranges, also shut off gas
• Support the handle while removing/installing screws to avoid stressing glass or trim
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Keep track of any decorative end caps or spacers for reassembly

A self-tapping screw used to fasten appliance panels and components where a threaded hole is formed as the screw is driven. Provides a secure hold for trim, brackets, and light assemblies during repairs. What it does:

• Cuts its own mating thread in sheet metal or thin plastic to secure panels and brackets
• Helps hold trim, access panels, or internal components in place
• Commonly used where a tapped hole is not present or repair requires a replacement fastener
• Can prevent loose parts and rattles caused by missing or damaged screws

• Unplug the appliance before servicing to avoid electrical or mechanical hazards
• Use the correct screwdriver or bit to avoid stripping the screw head
• Start the screw straight and apply steady pressure; do not overtighten to avoid cracking plastic or stripping metal
• Replace only with the exact part number to ensure proper fit and function

This door switch is a push-button electrical switch that detects when a fridge or freezer door is opened and closed, helping control lights and electrical features. It provides a direct, replaceable way to restore proper door sensing. What it does

• Opens and closes the circuit when the door moves, allowing interior lights and related controls to turn on/off.
• Commonly replaced when interior lights stay on or fail to turn on when the door opens.
• Helps prevent unnecessary compressor runtime when the door is detected as open.
• Compatible with cabinets that use a push-button style door switch mounted in the cabinet or door frame.

• One door switch (single push-button switch)

• Always disconnect power to the appliance before starting replacement to avoid electrical shock.
• Access typically requires removing the door gasket or inner door panel; retain screws and clips for reassembly.
• Replace by unplugging the old switch connector and installing the new switch in the same orientation; verify firm connector seating.
• After installation, restore power and cycle the door to ensure the switch operates lights and controls as expected.

This stacking kit secures a 24" dryer on top of a matching 24" washer to save floor space and keep the two units aligned. It provides a stable connection that helps reduce shifting and excessive movement during use. What it does:

• Locks the dryer to the washer to prevent the top unit from sliding or tipping
• Helps maintain proper alignment between stacked units for safe operation
• Reduces noise and vibration caused by movement between cabinets
• Designed for 24" width washer/dryer pairs

• Follow the appliance manufacturer's stacking instructions and torque specs
• Unplug both appliances and shut off water before beginning installation
• Use two people to lift and position the dryer safely onto the washer
• Verify units are level and connections are secure before use

This outer door window is the replacement glass panel that restores visibility and the finished exterior of the oven door. It provides a clear viewing surface while maintaining the door's original appearance and function. What it does:

• Replaces cracked, chipped, or scratched outer glass on the oven door
• Restores a clear viewing area to monitor cooking without opening the door
• Helps maintain the door's sealed appearance and prevents heat loss due to visible damage
• Matches OEM fit and finish for proper alignment and appearance

• Disconnect power to the appliance before beginning any repair
• Handle glass with care and wear cut-resistant gloves and eye protection
• Removal of the door and inner panel may be required for access; follow the manufacturer's service instructions
• If adhesive, clips, or trim are damaged, replace those items separately as needed

This door hinge is the replacement pivot that supports and lets the refrigerator door open and close smoothly. Restores proper door alignment and secure mounting for safe, reliable operation. What it does:

• Provides the pivot point that supports the refrigerator door and keeps it aligned
• Enables smooth opening and closing of the door
• Helps prevent door sag, rubbing, or uneven gaps that affect sealing
• Can reduce hinge-related noises or binding when operating the door

• One door hinge

• Disconnect power to the appliance and remove any food or shelves that block access before starting
• Support the door while removing fasteners; align hinge and tighten hardware securely during installation
• Check door alignment and gasket seal after installation; adjust hinge position if needed

A replacement control knob assembly that restores safe, positive control of your appliance's settings. Replaces a cracked, stripped, loose, or missing knob so you can select functions and settings reliably. What it does:

• Provides a secure grip and smooth rotation for selecting temperature or function settings
• Replaces knobs that are cracked, worn, stripped, loose, or missing
• Restores proper control engagement when the original will not turn or won't stay set
• Matches OEM fit and mounting for a straightforward swap

• Always disconnect power to the appliance before starting any repair
• Most installations are push-on: remove the old knob by pulling straight off, then push the replacement onto the control shaft until fully seated
• If the knob is tight or stuck, gently wiggle while pulling; avoid prying on surrounding surfaces

This replacement filter cover restores the water-filter access door so the filter stays secured and the filter bay stays sealed for reliable water flow and easy filter changes. It's a direct-fit service part for compatible GE refrigerators. What it does:

• Secures the water filter in its housing so the cartridge stays seated during operation
• Helps keep the filter compartment sealed against dust and debris
• Prevents the filter from falling out or shifting while the fridge door is opened and closed
• Reduces the chance of water seepage around the filter area when properly installed

• Turn off the refrigerator's water supply and open the fridge door before replacing the cover.
• Remove the old cover by unlatching or pulling as required, then snap or slide the new cover into place until it latches.
• Inspect the filter seal and seating; replace the water filter if damaged or worn.

This door strike attaches to the dryer door and engages the cabinet catch and door switch so the door latches securely and the dryer can run. Replace a worn or broken strike to restore reliable door closure.

• Mounts on the dryer door; provides the latch post that inserts into the cabinet catch
• Activates the door switch when closed to allow the cycle to start
• Common symptoms: door won't latch or pops open during use
• Dryer won't start unless the door is held shut; visible cracks or a missing strike

• Disconnect power before servicing
• Open the door and remove the existing strike from its mounting location
• Position the new strike in the same orientation and secure it as originally installed
• Close the door and test operation