Gfd28gmleees Parts

Gray door hinge end cap assembly for refrigerators. Covers and protects the hinge mechanism. Replace if cracked, broken, or missing for a complete look.

Exterior cover for the refrigerator ice bin that restores a flush appearance and keeps ice contained. Replaces a cracked, warped, or broken door.

Right-hand side support bracket for bottom-mount refrigerators. Replaces broken, cracked, or missing structural support. Installs on interior side.

Guides and supports your freezer drawer as it slides open and closed. Replace if the track is cracked, broken, or worn, causing misalignment or rough movement.

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

This SCR (silicon controlled rectifier) controls high-current switching in the appliance's power circuit to enable reliable on/off control of heating or motor circuits. Designed for direct replacement of the original SCR component. What it does:

• Acts as a solid-state switch to control power to heating elements or motors when triggered by the appliance control board.
• Helps regulate current during start-up and run cycles to maintain proper operation of the appliance.
• Failures can cause symptoms such as no heat, intermittent operation, or the appliance not powering its load.
• Matches the OEM mounting and stud terminal configuration for proper electrical connection.

• One SCR component (8-32 stud) as pictured.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Use proper tools for the 8-32 stud terminals and ensure secure electrical and heatsink connections.
• Inspect mounting surfaces and replace any damaged hardware or thermal pads as needed for safe operation.

A replacement 8-18 x 3/4 flanged pan-head screw used to secure panels, trim, and components. Restores proper fit and stops loose parts from rattling or shifting, helping appliances operate quietly and safely. What it does

• Fastens panels, brackets, trim pieces or assemblies that use an 8-18 thread screw
• Replaces missing or stripped screws that cause loose or vibrating parts
• Helps maintain proper alignment of panels and covers
• Prevents gaps that can allow movement or noise during operation

• One 8-18 x 3/4 flanged pan-head screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread the screw in by hand first, then snug; avoid over-tightening
• If underlying threads are damaged, replace the mating fastener or insert as needed

This condenser support is the replacement mounting bracket that holds the refrigerator condenser or condenser coil securely in place, helping maintain proper clearance and airflow for reliable cooling performance. What it does:

• Secures the condenser or condenser coil to the cabinet to prevent movement or vibration
• Maintains correct condenser positioning to support consistent airflow and heat dissipation
• Helps reduce rattling or noise caused by a loose condenser assembly
• Supports overall cooling reliability by keeping components aligned

• One condenser support bracket

• Installation requires basic hand tools; disconnect power before beginning any repair
• Handle sharp sheet-metal edges carefully to avoid cuts
• Reinstall any removed panels or fasteners to restore proper airflow paths

A replacement rubber mounting cushion that isolates and secures the refrigerator compressor to reduce vibration and noise. Restores proper compressor seating to help lower vibration transfer and prevent premature wear. What it does:

• Cushions the compressor to absorb vibration and reduce noise during operation
• Helps keep the compressor properly aligned and secured to the mounting bracket
• Can reduce rattling or buzzing that indicates worn or missing mounts
• Protects mounting hardware and body panels from metal-on-metal contact

• One compressor grommet

• Turn off power to the appliance and unplug before servicing
• Inspect surrounding mounts and hardware; replace any damaged fasteners
• Grommet installs between compressor and mounting bracket; reuse OEM orientation

This right-hand outer stop door is the external stop piece that helps the appliance door close and stay aligned. It restores proper door movement and prevents overtravel for smoother, more secure closing. What it does

• Acts as the outer stop/bumper on the right-hand side of the door assembly to limit travel.
• Helps the door latch and align correctly when closing.
• Commonly replaced if the stop is cracked, worn, or broken, causing misalignment or noisy closing.
• Works as part of the door's trim/stop system to protect adjacent components from impact.

• Disconnect power or unplug the appliance before beginning any work.
• Removal/installation may require removing door trim or fasteners; keep hardware for reuse.
• Handle plastic trim pieces carefully to avoid cracking; use proper trim tools where available.

This 1/4-20 x 3/4 machine screw fastens appliance panels and components for a secure fit, helping stop rattles and keep parts aligned during normal use. It's a direct-fit fastener used where the original threaded screw is required. What it does:

• Secures panels, brackets, and internal components to prevent movement and vibration
• Restores proper fit where a stripped, loose, or missing screw allowed rattling or misalignment
• Provides the correct thread size and length to match factory-mounted threaded inserts
• Helps maintain electrical and mechanical connections that rely on proper fastening

• One 1/4-20 x 3/4 machine screw

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or socket to avoid stripping the head
• Tighten snugly but do not overtighten to avoid damaging threads or plastic parts
• Replace the mating insert or panel hardware as needed