Gfe28hmhfesges Parts

This left-side lower freezer slide restores smooth drawer movement and proper alignment in the freezer compartment. It replaces a worn or damaged slide to help the drawer open and close reliably. What it does:

• Replaces the left lower freezer drawer slide that guides the drawer on its track
• Restores smooth, even sliding and prevents the drawer from sticking or binding
• Helps keep the drawer properly aligned so it opens and closes without catching
• Useful when the existing slide is bent, cracked, or worn and affects drawer operation

• Disconnect power and remove food from the drawer area before starting
• Typically installs onto the freezer cabinet and drawer track; basic hand tools may be required
• Align slide with factory mounting points and secure hardware; test drawer movement after installation

This is a replacement round-head screw sized 10-24 x 5/8 in. It secures trim, panels, and internal components so parts stay aligned and appliances run quietly and safely. What it does

• Fastens panels, brackets, and trim pieces in place
• Prevents loose parts that can rattle or cause misalignment
• Replaces missing or stripped screws to restore secure mounting
• Works where a 10-24 x 5/8 round-head screw is required

• Disconnect power before servicing the appliance
• Use the proper screwdriver or nut driver to avoid stripping the head
• Align parts before tightening and thread gently to avoid cross-threading
• Do not over-tighten; stop when snug to prevent panel distortion

This 1/4-20 hex washer head screw secures panels and components in place, restoring proper fit and eliminating movement. It fits common appliance assemblies that use a 7/8" long, 1/4-20 threaded fastener. What it does:

• Fastens panels, brackets, and assemblies that use a 1/4-20 thread
• Restores secure fit when original screw is missing, stripped, or loose
• Helps stop rattling, vibration, and misalignment caused by loose hardware
• Matches common OEM head style for tool-ready installation with a socket or wrench

• Disconnect power to the appliance before servicing where applicable
• Use the correct 1/4-20 socket or wrench; install hand-tight then snug—do not overtighten
• Replace like-for-like: head style, thread size, and length before installing
• If fastener holes or threads are damaged, repair or retap before reuse

This clutch coupling connects the washer motor/clutch to the agitator so the tub agitates properly during the wash cycle. Replaces a worn or broken coupling to restore normal agitation and reduce slipping or grinding. What it does:

• Transfers motor/clutch rotation to the agitator so clothes move during wash cycles.
• Commonly used when the washer spins but does not agitate or when agitation is weak.
• Helps eliminate slipping, grinding, or unusual noise from a failing coupling.
• Works as the mechanical link between the drive system and agitator assembly.

• One clutch coupling as pictured and specified by the OEM.

• Disconnect power and water supply before starting any repair.
• Basic mechanical skills and common hand tools required; follow OEM disassembly steps for safe access.
• Inspect related parts (agitator, drive shaft, clutch) for wear and replace as needed.

This LED light shield protects and diffuses the refrigerator's LED lighting, restoring even illumination and preventing direct exposure to the lamp. Replace a cracked, yellowed, or missing shield to improve light distribution and appearance. What it does:

• Covers and protects the LED light assembly from damage and debris.
• Diffuses LED output for softer, more even interior lighting.
• Replace if the shield is cracked, broken, warped, or discolored.
• Helps prevent direct glare from exposed LEDs for safer visibility.

• One LED light shield / cover.

• Disconnect power to the appliance before starting any work.
• Handle the shield carefully—plastic can crack; avoid overtightening fasteners.
• Install by aligning with existing mounting points or clips; do not force into place.
• Inspect the LED module and wiring.

A left-hand closure door assembly that replaces a worn or broken door closure to restore proper sealing and smooth drawer/door operation. Helps stop drafts and keeps compartments closing correctly for reliable performance. What it does

• Guides and supports the left-side door/drawer as it closes to ensure proper alignment.
• Helps form a tight seal to reduce air leakage and maintain interior temperature.
• Prevents rattling or catching that can occur when the closure is damaged or worn.
• Commonly replaced when the door doesn't stay closed, binds, or leaves a visible gap.

• Disconnect power to the appliance before starting any repair.
• Basic hand tools are typically required; access may involve removing a drawer or trim panel.
• Handle parts carefully to avoid damaging surrounding panels or gaskets.

A left-hand hinge center assembly that secures the refrigerator door at the center hinge to restore proper support and alignment. Replaces a worn or damaged hinge center to reduce door sagging and improve smooth opening. What it does:

• Provides a stable pivot point at the door's center hinge for correct alignment and support.
• Helps stop door binding, uneven gaps, and rubbing by restoring proper hinge geometry.
• Transfers load between upper and lower hinge halves so the door closes and seals correctly.
• Designed as a direct-replacement service part matching OEM fit and function.

• Support the door before starting—remove or brace the door to prevent it from falling.
• Disconnect power to the appliance if working near electrical components or the light switch.
• Remove hinge fasteners and replace with the new hinge center; tighten hardware securely but do not over-torque.
• Check door alignment and operation after installation; adjust hinge mounting as needed for an even gap.

This damper controls airflow to the refrigerator vegetable/produce pan to help maintain proper humidity and cooling for fresh food. Replacing a worn damper restores balanced airflow and helps keep produce crisper. What it does:

• Opens and closes the vent to regulate cold air entering the vegetable/produce pan
• Helps maintain proper humidity and temperature in the crisper area
• Commonly used when produce becomes wilty or the fresh-food compartment cools unevenly
• Prevents overcooling or insufficient airflow to the crisper drawer

• Disconnect power to the appliance before attempting repair
• Remove shelves/drawers as needed for access; handle glass shelves carefully
• Verify damper orientation and secure mounting before reassembly

This left-side freezer holder slide secures and guides the freezer drawer for smooth opening and closing. Replacing a worn or broken slide restores proper drawer alignment and helps prevent sagging or sticking. What it does:

• Supports the freezer drawer on the left side and keeps it aligned during use
• Guides drawer movement for smooth opening and closing
• Replaces damaged, bent, or missing slides that cause binding or uneven drawer travel
• Helps prevent the drawer from sagging, slipping, or coming off its track

• Disconnect power before servicing to avoid electrical hazards
• Remove freezer contents and a drawer or panel as needed for access
• Compare the old slide to ensure correct left/right orientation before installing
• Use basic hand tools; do not force parts—replace any damaged mounting hardware

This silicon controlled rectifier (SCR) switches and regulates power to heating or motor circuits, helping the appliance control temperature and run cycles reliably. It's a direct-fit electronic switching component used in a variety of control systems. What it does:

• Acts as an electronic switch to regulate AC power to heating elements or motors
• Helps control temperature output and maintain consistent cycle performance
• Can prevent unwanted continuous current flow when functioning properly
• Commonly replaced when ovens, ranges, or dryers fail to heat or cycle correctly

• One silicon controlled rectifier (SCR) as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the SCR by its body; avoid touching terminals and static-sensitive areas
• Verify proper orientation and secure mounting; follow OEM wiring and torque practices

A replacement 1/4-20 screw that secures panels, brackets, and components on compatible appliances for reliable fit and safe operation. Use this fastener to restore proper assembly and reduce rattles or loose parts. What it does:

• Threads into 1/4-20 tapped holes to hold panels, braces, or hardware
• Restores secure attachment where a missing or stripped screw allowed panels or trim to shift
• Helps eliminate vibration noise caused by loose fasteners
• Matches OEM fit for correct alignment and clearance

• Disconnect power to the appliance before servicing to avoid electrical hazards
• Use the correct driver or socket to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten securely but do not overtighten
• Keep hardware and small parts away from children and pets

A hex washer-head screw that secures panels and components in household appliances, helping restore stable, rattle-free mounting. Ideal when a mounting screw is missing, stripped, or rusted. What it does:

• Fastens panels, brackets, and internal components with a 1/4-20 thread for secure connections
• Replaces missing or damaged screws that cause loose panels or vibration noises
• Restores proper alignment of parts to prevent rattling and wear
• Works where a hex washer-head profile is required for flush, locked seating

• One hex washer-head screw, 1/4-20 x 3/4

• Use the correct 1/4-inch hex or socket driver to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Do not overtighten; snug until secure to avoid damaging threads or parts
• If screw threads are damaged, replace with the matching OEM part for best fit

This right-hand slide bracket assembly replaces the damaged or worn guide that supports a refrigerator/freezer drawer, restoring smooth, stable opening and closing. It mounts on the cabinet side to guide the drawer slide. What it does:

• Provides the right-side support and track for a drawer slide to engage and move smoothly
• Prevents the drawer from binding, tilting, or falling out when opening or closing
• Restores proper alignment for even drawer operation
• Helps eliminate scraping, sticking, or noisy drawer movement

• Remove all contents from the drawer and open to access the bracket before starting
• Basic hand tools (screwdriver or nut driver) are typically required; keep screws and fasteners from the old bracket for reuse if undamaged
• Disconnect power or follow appliance-specific safety procedures before working near electrical components

This diverter and badge assembly replaces the dispenser diverter on compatible refrigerators, restoring proper flow direction and the finished exterior badge for the dispenser area. It helps stop leaks and stabilizes the dispenser trim. What it does:

• Directs dispenser water/ice flow through the correct outlet to prevent misdirected dispensing
• Secures the dispenser badge/trim to the appliance front for a finished appearance
• Helps stop leaks or drips caused by a damaged or worn diverter
• Reduces wobble or looseness at the dispenser face when the badge/clamp is intact

• One diverter & badge assembly

• Disconnect power (and water supply if applicable) before beginning work
• Access may require removing the dispenser bezel or door trim—follow your model's service instructions
• Handle plastic components gently to avoid cracking; replace any damaged fasteners or seals

The Basket Bottom Asm is an OEM part for GE refrigerators. This assembly is specifically designed to fit in the bottom freezer compartment, providing a convenient and organized storage solution for your frozen foods.

A bad bottom freezer basket assembly can occur due to wear and tear, accidental damage, or other factors. If you notice symptoms such as broken wires, a loose fit, or difficulty in sliding the basket, it may be time to replace it with a new one.

Symptoms of a bad bottom freezer basket assembly include:

• Broken wires
• Loose fit in the freezer compartment
• Difficulty in sliding the basket in and out

Improve your freezer storage and organization by replacing the faulty bottom freezer basket assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This left-side vegetable pan is the replacement food-storage tray that holds produce and fits into the refrigerator crisper area for organized storage. It restores proper support and containment for fruits and vegetables. What it does:

• Provides a stable tray for storing fruits and vegetables in the crisper compartment
• Replaces cracked, warped, or broken pans that can let produce sit unevenly or fall through
• Helps keep items contained and easier to organize when the drawer is removed
• Works with the refrigerator's crisper assembly to maintain normal storage function

• One left-side vegetable pan

• Remove food and any loose components before installing to avoid damage or injury
• Slide the pan into the left crisper slot until it seats; ensure proper alignment with drawer rails
• Handle glass or plastic panels carefully to avoid chips or cracks