Ghdf360rss Parts

Specs: 10-32 gxtt flp.59

This flapper vent is the replacement exhaust flap that helps control dryer airflow and keeps outside air, pests and debris from entering the vent when the dryer is off. Fits many GE dryer exhaust housings. What it does

• Opens during dryer operation to let moist air escape and closes when the dryer is off to block backdrafts.
• Restores proper airflow when a damaged or stuck flap is preventing venting.
• Helps reduce outside odors, drafts and pest entry through the exhaust opening.
• Works as a simple mechanical replacement—no electrical connections.

• Disconnect the dryer from power and, if applicable, turn off gas before servicing.
• Access the exterior vent or the dryer exhaust housing; replacement typically secures with screws or snaps into the vent housing.
• Inspect and clean the vent duct and housing before installing the new flap to ensure proper operation.

This is a replacement fastener screw used to secure panels and components on compatible appliances, restoring proper fit and reducing movement. It's a simple, direct replacement when an original screw is missing or damaged. What it does:

• Secures access panels, covers, or internal components to prevent rattling and movement
• Helps maintain proper alignment of parts so doors and panels close correctly
• Replaces missing, stripped, or broken screws that can cause loose parts or noise
• Restores the appliance's original fit where a matching OEM fastener is required

• One replacement screw

• Turn off and unplug the appliance before starting any repair
• Use the correct driver and avoid over-tightening to prevent stripping threads
• If the original screw was holding electrical components, ensure power is disconnected and follow OEM safety instructions

This part is a genuine OEM lower rack assembly made for use with various models of dishwashers.The lower rack assembly slides into the lower portion of the dishwasher to allow the user to easily load the appliance as well as hold the dishes still during the wash cycle and make sure they can be properly cleaned. Over time, this part might become dented, bent, snapped, worn, or otherwise rendered ineffective, requiring replacement. No special tools are needed to replace this part. Simply slide out the old rack and replace it with the new one.This OEM part is manufactured by General Electric and has been sourced directly from the manufacturer. This lower rack assembly is manufactured from high-quality, durable, non-corrosive materials to ensure the best possible quality. It is an authentic replacement part and thus is compatible with various models of dishwashers that have been made by brands that include General Electric, Hotpoint, and RCA.

This lock nut assembly kit replaces a worn or missing locking nut that secures threaded fasteners on dishwasher components. It restores secure fastening to help stop movement, noise, or loose panels. What it does:

• Provides a threaded locking nut that holds mating fasteners in place on dishwasher assemblies
• Helps prevent loosening from vibration that can cause rattling or misalignment
• Commonly used where a nut must resist backing off without adhesive
• Compatible with the original mounting locations that use a captive/locking nut design

• Disconnect power to the dishwasher before accessing internal components
• Verify you are replacing the exact nut for the affected mounting point; hand-start threads to avoid cross-threading
• Tighten securely but avoid overtightening to prevent thread or component damage
• Keep track of screws and fasteners and test operation after reassembly

This is a stainless-steel outer door panel that restores the appliance's exterior appearance and provides the finished surface for the door assembly. It replaces a damaged, dented, or scratched outer door skin to improve looks and protect internal components. What it does:

• Serves as the outer skin for the refrigerator/freezer door, forming the visible exterior surface.
• Protects inner door components, insulation, and wiring from damage and moisture.
• Restores a flush, uniform appearance when the original panel is dented, scratched, or corroded.
• Compatible with factory mounting points to mate with the existing inner door and trim.

• One stainless-steel outer door panel.

• Handle, trim, insulation, and hardware are only included if explicitly listed.
• Disconnect power and remove stored items from the door area before beginning work to prevent injury or damage.
• Use caution with sharp edges and support the door to avoid dropping or bending the panel during installation.

 The Upper Arm Spray Assembly is an OEM part for GE dishwashers. It is responsible for distributing water evenly throughout the dishwasher during the cleaning cycle, ensuring all dishes are thoroughly cleaned. The arm measures approximately 11 inches long.

You should replace the upper arm spray assembly if it becomes clogged, damaged, or worn out. Causes of a bad spray assembly can include mineral buildup from hard water, food particles blocking the spray holes, or physical damage such as cracks or breaks.

Symptoms of a bad upper arm spray assembly include:

• Poor cleaning performance, with dishes coming out dirty
• Uneven water distribution inside the dishwasher
• Visible cracks or blockages in the spray arm
• Unusual noises during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Upper Spray Arm Bearing is an OEM part for GE dishwashers. It supports the upper spray arm, allowing it to rotate smoothly and distribute water evenly throughout the dishwasher. This ensures that all dishes receive a thorough cleaning during each cycle.

Over time, the upper spray arm bearing can wear out or become damaged. Causes of a bad bearing can include repeated use, mineral buildup from hard water, or physical damage due to mishandling.

Symptoms of a bad Upper Spray Arm Bearing include:

• The upper spray arm not rotating properly
• Ineffective cleaning of dishes on the upper rack
• Unusual noises during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Interlock Switch Assembly is an OEM part for GE dishwashers. It is designed to ensure the dishwasher door is securely closed before the wash cycle begins, preventing leaks and ensuring the appliance operates safely.

Causes of a bad interlock switch can include wear and tear from frequent use, electrical issues, or physical damage to the switch or its housing. A malfunctioning switch can prevent the dishwasher from starting or cause it to stop mid-cycle.

Symptoms of a bad door interlock switch assembly include:

• Dishwasher not starting
• Interruption of wash cycles
• Door not latching securely
• Error codes related to door latch issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Gasket Spring is an OEM part for GE dishwashers. It plays a crucial role in maintaining a tight seal around the dishwasher door, ensuring that water does not leak during operation. This spring helps keep the door gasket in place, providing a reliable and consistent seal.

Over time, the gasket spring can wear out, lose tension, or become damaged due to repeated use and exposure to the dishwasher’s high temperatures and moisture. A faulty spring can compromise the effectiveness of the door gasket, leading to potential leaks and inefficient washing cycles.

Symptoms of a bad gasket spring include:

• Water leaking from the dishwasher door
• Difficulty closing or latching the dishwasher door securely
• Reduced cleaning performance due to improper sealing

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Flood Switch Assembly is an OEM part for GE dishwashers. This part detects water levels and prevent overfilling by shutting off the water supply if a potential flood condition is detected. 

Causes of a bad flood switch assembly can include electrical failures, wear and tear over time, or damage from water exposure. 

Symptoms of a bad flood switch assembly include:

• The dishwasher not filling with water properly
• The dishwasher overfilling or leaking
• Error codes related to water levels
• The dishwasher not starting or stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.