Gld3600l00bb Parts

This dishwasher float sits in the tub and works with the float switch to control the fill level and prevent overfilling. Replace it if cracked or sticking to restore reliable water level control and help avoid leaks.

• Rises with the water level to trigger the float switch and stop filling at the correct point
• Helps prevent overfilling and door leaks
• Common symptoms of a damaged or obstructed float include continuous filling, overfill/leaks, or no/insufficient fill
• Restores consistent water level sensing when the original float is worn or missing

• Disconnect power and turn off the water supply
• Open the door and remove the lower rack
• Remove the float cover; pull the old float straight up and clear any debris from the well
• Insert the new float and verify free up-and-down movement before reassembly and testing

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

Filter only. Fine filter not included.

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

This inlet cover is a replacement trim piece that protects and finishes the washer's water inlet area, restoring a clean appearance and guarding internal inlet components from dirt and accidental contact. What it does

• Covers the water inlet opening and surrounding inlet assembly for a finished look
• Helps shield inlet valves and connections from debris and incidental contact
• Maintains proper alignment and fit of the inlet area trim
• Restores cosmetic appearance after damage or loss of the original cover

• One inlet cover

• Disconnect power and shut off water supply before starting any work
• Access may require removal of the washer top or control console depending on model
• Typically secures with clips or a few screws; have a screwdriver set on hand
• Replace if cracked or broken—do not attempt to use a damaged cover

This mounting bracket secures the dishwasher tub or inner components to the cabinet or frame, helping keep the appliance stable during cycles and preventing movement or misalignment. What it does:

• Provides a secure attachment point between the dishwasher and the cabinet or chassis
• Helps reduce rattling, shifting, and vibration during operation
• Keeps inner panels and assemblies aligned for proper door operation
• Supports correct positioning that can prevent wear on adjacent parts

• One dishwasher mounting bracket

• Intended for users comfortable with appliance repair; disconnect power and shut off water before starting
• Typical installation uses screws or clips—retain original fasteners unless replacement fasteners are specified
• Inspect surrounding mounting points and hardware; replace any damaged screws or tabs for a reliable fit

A replacement switch assembly that restores user control of the affected function by completing the electrical circuit when operated. Fits Frigidaire appliances and provides a direct replacement to return controls to normal operation. What it does

• Acts as the user-operated electrical switch that turns a specific function on or off.
• Replaces a failed or intermittent switch that causes the appliance function to not start or stop.
• Helps correct symptoms such as unresponsive buttons, intermittent operation, or no power to the controlled circuit.
• Works as a direct component-level replacement—no control board required when the switch itself is the issue.

• One switch assembly as shown.

• Disconnect power (unplug appliance or shut off circuit breaker) before beginning any work.
• Access may require removing a control panel or trim; keep fasteners organized for reassembly.
• Handle the new switch carefully to avoid bending terminals; verify secure connections before restoring power.

This kit replaces the appliance's main control electronics and tactile user interface so the appliance responds correctly to button presses and control inputs. Restores control functions and user feedback when interface components fail. What it does:

• Replaces the main control board that manages appliance cycles and electronic functions.
• Replaces the tactile/user interface board (touchpad) that registers button presses and sends commands.
• Commonly used when controls are unresponsive, buttons or touchpad won't register, or the display/control panel behaves erratically.
• Resolve intermittent operation or failure to start caused by faulty control or interface electronics.

• Disconnect all power to the appliance before beginning work to avoid shock or damage.
• Handle circuit boards by the edges and avoid static discharge; use a grounded wrist strap if available.
• Keep all screws and mounts from the original assembly for reinstallation; some components may require transferring connectors or brackets.

This mounting bracket secures the dishwasher rinse module/dispenser assembly so the dispenser stays properly positioned for reliable rinse-aid delivery. A correctly seated bracket helps prevent dispenser misalignment and related rinse-aid issues. What it does:

• Holds the rinse module/dispenser firmly in place inside the dishwasher tub or door
• Keeps the dispenser aligned so rinse aid can be released as designed
• Helps prevent dispenser rattling, shifting, or partial seating during cycles
• Can reduce symptoms like poor rinsing, visible spots, or uneven rinse-aid release

• Disconnect power to the appliance before starting any work for safety
• Basic hand tools (screwdriver, nut driver) are typically needed; follow OEM instructions
• Align the bracket and secure fasteners without over-tightening to avoid damage

This air diverter assembly routes and redirects airflow inside the appliance to help maintain proper venting and circulation. Replaces a worn or broken diverter to help restore normal airflow and reduce venting issues. What it does:

• Directs airflow between ducts and chambers to maintain intended ventilation paths
• Helps prevent air from bypassing heating elements or sensors
• Can reduce symptoms like uneven drying, long cycles, or reduced airflow
• Stops rattling or unusual air-noise caused by a broken or loose diverter

• One air diverter assembly

• Disconnect power before beginning any repairs
• Access may require removing the appliance back panel or cabinet; keep track of fasteners
• Inspect mating surfaces and seals; replace damaged seals or gaskets for best performance

no.8 - 10 , 3/8 phillips