Glet1031fso Parts

A small locating pin used to align and secure parts during assembly, helping panels and components sit correctly for reliable operation. Ideal when a worn or missing pin causes fit or alignment issues. What it does:

• Positions and holds panels, trim, or assemblies in the correct location during reassembly
• Prevents shifting or misalignment of covers and access panels
• Restores proper fit where a bent, broken or missing pin causes loose trim or gaps
• Small, simple replacement that addresses common fit/fitment symptoms

• Disconnect power and unplug the appliance before beginning any work
• Use basic hand tools; avoid forcing parts into place to prevent damage
• Inspect surrounding components for damage and replace if worn

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks

Pan hd phillips ,6-32 x 0.337 ,dog point

A small replacement retainer clip used to secure interior trim or components so panels and shelves stay in place. Replacing a worn or broken clip restores a snug fit and reduces rattling or loose parts. What it does

• Holds trim, panels or small components in place to prevent shifting
• Prevents rattling and keeps parts aligned for proper operation
• Replaces cracked, broken or missing clips that allow parts to sag or fall
• Works wherever the OEM clip design is specified for a secure snap-fit

• Clip

• Disconnect power before servicing appliances with electrical components
• Remove surrounding trim or components carefully to access clip location
• Press or snap the clip into place; avoid forcing to prevent damage
• Keep small parts away from children and pets during installation

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

This transmission assembly drives the agitation and spin cycles by transferring motor power to the tub. Replacing a worn transmission helps restore proper wash action and spin performance.

• Converts motor rotation into the geared motion needed for wash (agitate) and spin
• Shifts between agitation and spin modes during the cycle
• Common failure signs: no or weak agitation; no spin or slow spin
• Other symptoms include loud grinding/rumbling, oil leaking from the center area, or the motor running while the tub doesn't move

• Disconnect power and water; move the appliance to a stable work area and use proper lifting support
• Access the drive assembly from below; support the tub/frame to prevent tipping
• Mark component orientation, remove fasteners and drive components as needed, and transfer any reusable parts from the original unit
• Tighten mounting hardware evenly, then run a test cycle and check for leaks