Glet1031sc0 Parts

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

This is a heat shield insulator that mounts on the inner side of the dryer door in a stacked laundry center or washer/dryer combo unit. It prevents excessive heat from transferring through the door during drying cycles, protecting the outer door surface and improving energy efficiency. Replace this insulation if it is torn, deteriorated, or missing, which can cause the door to become excessively hot to the touch or reduce drying performance.

This is a small C-clip or retainer ring that secures the idler pulley to its bracket on a laundry center. It keeps the pulley in place so the drive belt maintains proper tension against the drum. Replace this ring if the idler pulley has come loose, the drum belt slips or falls off, or the dryer drum does not spin properly.

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

This is the blower housing that encloses the dryer blower wheel in a washer/dryer combo or laundry center unit. It directs airflow from the dryer drum through the exhaust system to properly vent heat and moisture. Replace this housing if it is cracked, warped, or damaged, which can cause poor drying performance, unusual noises, or air leaks during the drying cycle.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

Washer overflowing or filling when off? This water inlet valve controls water flow to stop leaks and restore proper fill cycles. Moderate DIY repair.

Replaces a cracked or broken splash tub cover assembly on your washer. Installs around the tub to protect internal components from water damage.

Connects your washing machine to the household water supply. Replace this flexible inlet hose if cracked, leaking, or worn to restore proper flow.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Secures the drain hose to prevent leaks and disconnection during spin cycles. Replace if cracked, loose, or causing water leakage. Verify fit with your model.

Shipping screw for washer drum transport stabilization. Remove before operation, save for future moves. Prevents drum damage during relocation.

Hex washer head screw for laundry centers. Secures panels and components during assembly. Replace if stripped, missing, or damaged during repairs.