Glhs36efsbo Parts

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Replace a cracked, broken, or missing handle mounting button on your refrigerator. This plastic bushing secures the door handle to the cabinet frame.

Decorative channel trim that covers the water supply tube on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Control box housing cover for refrigerators. Protects and encloses the defrost control board. Replace if cracked, broken, or missing to secure components.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Bearing plate for refrigerators. Provides structural support for rotating components. Replace if cracked, warped, or damaged to restore stability.

Secures the micro switch in your refrigerator's ice dispenser assembly. Replace if screw is rusted, stripped, or missing to properly mount the switch.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

This replacement name plate restores the exterior identification and branding on the appliance, improving appearance and readability of model information. It's a direct-fit cosmetic trim piece. What it does:

• Replaces a cracked, faded, scratched or missing name plate for a refreshed look
• Restores the readable appliance identification and branding on the exterior
• Helps protect the underlying surface from minor wear where mounted
• Useful when cosmetic damage makes labels hard to read or when preparing an appliance for resale

• One replacement name plate

• High-level installation typically requires removing the old plate and securing the new one in the existing mounting location
• Use correct fasteners or adhesive as originally installed; do not force or overtighten
• Clean and dry the mounting surface before installation to ensure proper fit and adhesion
• Handle carefully to avoid scratches; no electrical disconnection is normally required for cosmetic name plates, but follow appliance-specific safety guidance

Replacement mounting clip for freezers and refrigerators. Secures interior panels and trim to prevent rattling. Replaces broken or missing clips.