Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Alignment pin keeps washer door hinge positioned so the door closes evenly. Replace if cracked, bent, or missing to restore proper door fit and seal.
Replaced washer tub straps and a broken strap retaining clip. Read more
Grounding stud for top-load washers. Connects electrical ground wire to washer frame. Replace if stripped, corroded, or missing for proper grounding.
Size: 1/4 - 20 b.
OK kids, pay attention! This was my second attempt @ this repair. My first repair started leaking right away and had to be re-done about 6 months later. HERE IS THE PROBLEM!. In the video, you'll notice that (while putting it back together) when you put the square hole washer and split-ring over the shaft, they look to land atop the rubber seal, buy when you do this in real life, there is a gap between the seal and the washer. (This gap was close to a 1/4 inch). I THINK that the first time I... Read more
Size: 8-18 b.
Purchased new RPS Hall Effect sensor, pulled rotor and stator and installed new RPS module. Works fine after new sensor! Repair took about 30 minutes. Perfect! Read more
Grounding clip for top-load washers ensures proper electrical grounding. Replace if damaged, corroded, or missing to maintain safe operation. Verify fit with your washer model number before ordering.
Secures the counterweight to the washer drum assembly. Replace this bracket if it's cracked, broken, or causing rattling during wash cycles.
Wire tie retainer for refrigerators. Secures and organizes internal wiring. Replace if cracked, broken, or missing to keep wires properly bundled.
Timer knob for washer control panel. Replace this graphite-silver dial if cracked, broken, or missing. Easily installs on control panel shaft.
The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.
Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.
Symptoms of a bad Dryer Wire Tie include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Went to local stores appliance section for GE and asked The appliance person recommended finding parts thru AppliancePartsPros.com and walked us thru the process to order the parts. Read more
I replaced the ball and socket connection for the drum. After doing so, I realized that the belt had been stretched and the tension pulley was not putting enough tension on the belt to turn the drum. After ordering a new belt, extra screw that was lost while disassembling the dryer, and some high temperature lubricant for the drum ball and socket the dryer now runs as well as it did when it was new. Read more
Replaced drain hose and clamp. Read more
This is a small connector jumper wire used in the washer's control system to select the correct operating model or configuration. It plugs into the control board or wiring harness to ensure the washer runs the proper cycle programming for your specific unit. Replace this connector if your washer is not responding to cycle selections correctly or if the original connector is missing or damaged.
Flood hose for top-load washers. Connects tub to base to drain overflow water. Replace if cracked, leaking, or gasket is worn or damaged.
A foam insulation barrier that helps seal and protect refrigerator cabinet cavities from air and moisture intrusion. Replaces worn or damaged foam to support proper airflow and reduce the risk of frost buildup around internal components. What it does:
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.