Grmc2273cf Parts

If your refrigerator feature won't turn on or off, this electrical switch may have failed. Controls power to specific functions. Simple repair.

Fix a refrigerator that won't start, run, or respond to controls by replacing the failed electronic control board. Restores proper function to all components.

Replace your damaged or scratched refrigerator outer door panel to restore appearance and ensure a proper seal. Verify fit with your model number.

Refrigerator not cooling evenly or making unusual noise? The evaporator fan motor circulates cold air across the coil. Moderate DIY repair for most models.

Encloses and protects internal components from debris and moisture. Replace this cover if cracked, warped, or missing to restore a clean, finished look.

If your refrigerator light stays on or won't turn on when opening the door, the door switch likely failed. This switch controls interior lighting.

Small retainer clip that secures components, panels, tubes, or wires in place inside your refrigerator. Replace when worn, broken, or missing to restore fit.

This fan motor-and-blade assembly restores airflow in compatible Frigidaire refrigerators and freezers to help maintain even temperatures and reduce warm spots. It replaces a failed fan to improve circulation and appliance performance. What it does:

• Circulates air inside the fresh food and freezer compartments for more even cooling.
• Moves air across cooling components to help prevent localized frost and warm zones.
• Replaces noisy, stalled, or non-spinning fans that cause reduced cooling or unusual sounds.
• Supports proper airflow so the appliance can maintain set temperatures more consistently.

• Disconnect power before starting—unplug the appliance or shut off the circuit breaker.
• Access typically requires removing interior panels or the rear evaporator cover; retain fasteners.
• Handle blades carefully to avoid bending; ensure electrical connectors are fully seated.

Replaces the vertical center trim between refrigerator doors. Install when trim is cracked, warped, or missing to restore appearance and maintain proper door seal.

Secures the door handle to your refrigerator. Replace if screw is stripped, missing, or loose causing handle to wobble or detach from the door.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Fixes excessive frost buildup and ice on evaporator coils. This defrost heater melts accumulated ice to restore proper airflow and cooling performance.

Replace your refrigerator's damaged or dented stainless steel outer door assembly to restore appearance and proper seal. Confirm fit with your model number.

This right-side stainless steel freezer door assembly replaces a damaged or dented freezer door and restores a clean, finished exterior. Fits models that use the 5304537074 door and matches factory appearance and function. What it does:

• Replaces a bent, dented, or cosmetically damaged right freezer door to restore fit and seal
• Provides the outer shell that attaches to hinges and accepts interior panels and gasket
• Helps maintain proper freezer closure to support consistent cooling
• Matches OEM finish and mounting locations for a factory-like replacement

• Installer-level replacement; may require removing freezer door, hinge screws, and transferring trim or door liners
• Use proper support to prevent dropping the door; two-person lift recommended for safety
• Disconnect power and empty the door area as needed before starting work

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Structural housing for refrigerator icemaker components. Replace if cracked, broken, or damaged. Supports water routing and internal alignment.