Gsd3900 Parts

This is a replacement washer drive motor that powers the tub to spin and agitate, restoring normal wash and spin cycles. Fits specified GE top-load washers and matches OEM form and function. What it does

• Spins the wash tub to perform spin cycles and remove water
• Powers the agitation/oscillation action during wash cycles
• Commonly replaced when the washer won't spin, won't agitate, or hums without turning
• Helps eliminate intermittent power-to-motor issues when motor failure is the root cause

• One replacement drive motor

• Disconnect power before starting any repair to avoid electric shock
• May require removing the washer cabinet or access panels and detaching the old motor wiring and mounting screws
• Handle carefully — support the tub/drum as needed during motor removal and reinstallation

This switch interlock assembly secures the appliance door and completes the electrical circuit so the unit can start and run safely. Replacing a worn interlock restores reliable door sensing and helps ensure normal cycle operation. What it does:

• Detects and holds the door/lid closed so the appliance will start
• Completes the electrical pathway for motor and control circuits
• Prevents operation when the door is open or not fully latched
• Can stop mid-cycle or prevent starting when the interlock fails

• One switch interlock assembly

• Disconnect power (unplug or switch off the breaker) before replacing the part
• Handle mounting screws and wiring harness carefully; match connector orientation when reinstalling
• Verify door alignment and latch function before restoring power

This switch sensor is a direct-replacement sensing device that detects the position/state of a moving component and sends that signal to the appliance control for reliable operation. It restores correct sensing when the original fails. What it does:

• Detects and reports a component's open/closed or engaged/disengaged position to the control
• Helps the appliance start and change cycles only when the mechanism is in the correct position
• Can resolve symptoms such as no response from the control, intermittent operation, or cycles that won't advance
• Provides a direct electrical/mechanical interface between the moving part and the control system

• One switch sensor

• Disconnect power to the appliance before starting any repair
• Match this part number to the failed sensor before installing
• Handle wiring and connectors carefully; avoid forcing tabs or pins
• Test operation after installation and restore power only when all connections are secure

This support calrod assembly secures and positions the oven/range heating element so it heats evenly and stays stable during operation. Replaces a worn or damaged support to restore proper element alignment and reduce rubbing or sparking. What it does:

• Holds the tubular heating element in the correct orientation inside the oven or range
• Prevents the element from sagging, contacting interior surfaces, or vibrating during use
• Helps maintain consistent heating performance and reduces risk of element wear
• Common symptom: element rubbing, touching oven walls, or uneven heat distribution

• One support calrod assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Handle heating elements and support parts carefully to avoid bending or damaging the element
• Follow OEM service instructions for removal and reassembly; verify correct element alignment before restoring power

2 wire insulator.

This finished toe kick panel replaces the lower front trim on compatible GE washers and dryers to restore appearance and protect the cabinet base. It provides a clean, finished look and covers the gap between the appliance and the floor. What it does:

• Replaces a damaged, scratched, or bent toe kick to restore the appliance's exterior finish
• Covers and protects the cabinet base from dust, debris, and foot traffic
• Helps maintain a finished, factory appearance after repairs or cabinet work
• Fits where a finished front toe panel is required for proper cosmetic restoration

• Intended for cosmetic replacement; fit to your exact model before installation
• Remove power (unplug or shut off breaker) before accessing panels near controls; follow all safety precautions
• May require removal of lower access panels or screws; retain original fasteners unless replacements are provided

This is a replacement fastener screw used to secure panels and components on compatible appliances, restoring proper fit and reducing movement. It's a simple, direct replacement when an original screw is missing or damaged. What it does:

• Secures access panels, covers, or internal components to prevent rattling and movement
• Helps maintain proper alignment of parts so doors and panels close correctly
• Replaces missing, stripped, or broken screws that can cause loose parts or noise
• Restores the appliance's original fit where a matching OEM fastener is required

• One replacement screw

• Turn off and unplug the appliance before starting any repair
• Use the correct driver and avoid over-tightening to prevent stripping threads
• If the original screw was holding electrical components, ensure power is disconnected and follow OEM safety instructions

Black. 8-18 x 5/16 inch.

Bisque. 8-18 x 5/16 inch.

This long front panel replaces a damaged or worn control-area panel to restore the range's appearance and provide a secure mounting surface for control components. It fits the long control area used on select GE ranges. What it does:

• Replaces cracked, dented or heavily scratched front/control-area panels to improve appearance
• Provides the mounting surface and alignment for control switches and trim
• Helps keep internal components shielded from spills and debris near the controls
• Restores a flush fit where the original panel was warped or bent

• Disconnect power to the appliance (unplug or switch off breaker) before starting work
• Remove control knobs and any trim pieces to access mounting screws; keep original fasteners for reassembly
• Handle the panel carefully to avoid cuts from sharp edges and to prevent cosmetic damage
• Take care when disconnecting and reconnecting wiring;