Gss25wgpd Parts

Replaced shelves Read more

I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more

Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more

Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more

I had 2 parts that were cracked, so after changing the cracked parts as well as the dispenser switch, it was back to working normally. Simple to make the needed repairs and the videos provided on your website really helped in being prepared. Read more

I removed the drawers and old rails, and screwed in the new ones. It was very straightforward. Read more

I had to disassemble the ice bucket, there were three screws to remove the cover, one screw and a tension spring that holds the bar in place that controls ice cubes from crushed ice. The hardest part was removing the plastic chamber where the ice crushing blades are attached to the auger, I had to use a couple of butter knives to spread the outer ice bucket away from the inner ice chamber because they had those funky plastic lock-in tabs that lock the ice chamber in place to the ice bucket. I... Read more

Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more

Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more

I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more

Compressor overload switch broke in my hand when I removed it but replacing it and the start relay did not fix the problem. I troubleshot the control board with the help of videos from Grace Appliance (https://www.youtube.com/c/GraceAppliance/videos) and found fans were not getting power. I ordered an aftermarket control board that offered free returns but it kept cycling off and on every minute. I think it might have been overloaded because the main resistor in the evaporator fan drive... Read more

Replaced motor and solenoid cube along with dispenser auger. Simply watched video on repair and installation and really had no problem. My refrigerator is so old that one of the holes in the motor did not align properly. Had to drill another hole to mount the motor to the housing, took ten minutes. The ice auger took the longest as I was afraid of breaking the plastic housing trying to get the tabs to release. Had to watch the video twice to make sure I got the blades back in the right order.... Read more

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

1) By using google to find videos on why the door wouldn't close, I found out I needed new cams, those same videos also showed how to remove and replace the door. 2) Then by googling the fridge model number and the word 'cam', I was able to find the parts. 3) Taking the door off was simple, I needed a phillips head screwdriver to remove the hinge cover, however the screws in the hinge plate were so tight, I needed a side handle socket wrench to loosen them. 4) The door itself is not hard to... Read more

I cleaned the coils as best as I could with a special brush and replaced the seized up fan motor. Read more