Gsx9750wp0 Parts

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Spin tube assembly with drive spacer, bearing, and shaft seals. Replace if washer leaks from bottom or basket doesn't spin properly. Verify fit.

Fix washer leaking water on the floor with this bleach dispenser hose. Connects the bleach dispenser to the tub for proper dispensing during wash.

Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.

Supports the washer transmission shaft to reduce axial wear and noise. Replace when you hear grinding sounds or experience rough operation. Confirm fit with your model number.

This is a plastic splash shield assembly that sits on top of the washer tub, forming a seal between the tub and the outer housing. It helps prevent water from splashing out during the wash and spin cycles. Replace this part if you notice water leaking from the top of the tub area or pooling underneath the washer during operation.

Replacement shaft sleeve bushing for washers. Fits over rotating shafts to reduce friction and protect surfaces. Replace when worn, cracked, or missing.

Rear panel pad cushions and insulates the appliance's rear cabinet to reduce vibration, noise and rubbing against the back panel. Replacing a damaged pad helps stop rattles and protects internal components from wear. What it does:

• Provides rear-cabinet cushioning and thermal/abrasion protection for the back panel.
• Dampens vibration and reduces operational noise.
• Prevents direct metal-to-metal contact that can cause rubbing or wear.
• Common symptom fix: reduces rattling or vibrating noises from the appliance rear.

• Always disconnect power (and gas, if applicable) before starting any repair.
• Remove the rear access panel to access the pad; replace using the original mounting points, adhesive or clips.
• Inspect surrounding insulation and mounting hardware; replace any damaged fasteners.

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

Fix bleach dispenser leaking issues with this washer dispenser assembly. Delivers bleach and fabric softener at the right time during wash cycles.

Use with motor 357282.

Can't select wash cycles or knob won't turn? This rotary cycle selector switch restores proper cycle selection. Straightforward repair for most DIYers.

This bracket secures the washer motor to the machine frame and absorbs vibration during operation. Replace if the washer vibrates excessively, makes loud noises during agitation or spin cycles, or if the bracket shows visible damage.

Assorted fasteners, clips, and hardware for washer repairs. Replace missing or damaged clips during panel removal or component service. Verify fit with your model.

Replaces a cracked or broken washer tub ring. This plastic cover secures to the outer tub assembly. Order a new ring if yours is damaged or missing.