Gte181shdrss Parts

This freezer door stop cushions and limits the door's travel to protect the hinge and cabinet edge, helping the door close smoothly and preventing over-travel damage. Fits black trim locations on compatible freezers. What it does:

• Acts as a bumper to stop the freezer door from swinging too far
• Cushions impact, reducing stress on hinge components and cabinet
• Helps the door align and close flush to maintain seal performance
• Common symptom fix: door hits cabinet, scrapes, or sits unevenly

• Remove any food/obstructions and support the door before replacing the stop
• Usually a simple snap-in or screw-on replacement; small hand tools may be required
• Inspect surrounding hinge and trim for damage when replacing
• Follow all safety precautions; unplug unit or disconnect power before performing extended service

This evaporator harness is the factory replacement wiring assembly that connects the evaporator components so the refrigerator can complete defrost cycles and circulate cold air reliably. It restores secure electrical connections behind the evaporator coil. What it does

• Routes power and signals between the evaporator fan, defrost heater and temperature sensors/thermostat.
• Helps the defrost system operate properly to prevent excessive ice buildup on the evaporator.
• Restores reliable electrical connections that can stop intermittent fan or defrost operation.
• Commonly used when connectors are corroded, wires are damaged, or the harness is melted or brittle.

• One evaporator harness wiring assembly as shown.

• Disconnect power before accessing the evaporator compartment and any wiring.
• Remove interior panels and ice/water lines as required to reach the evaporator; follow your model's service manual.
• Match connector shapes and routing; do not force connectors—replace if pins or sockets are damaged.

This shelf cantilever wire assembly replaces a bent or broken refrigerator shelf support to restore stable shelf placement and weight-bearing capacity. It helps keep shelves level and prevents items from shifting or falling. What it does:

• Supports and secures a refrigerator shelf at the side wall mounting points
• Replaces worn, bent or broken cantilever supports that allow shelves to sag or drop
• Restores correct shelf height and alignment for safe storage
• Helps eliminate shelf movement and uneven loading that can cause spills

• Unplug the appliance or disconnect power before servicing to reduce shock risk
• Remove food and any items from nearby shelves before replacing the part
• Handle edges carefully; use basic hand tools to remove and install the support as needed

This plastic freezer door bin provides a replacement storage shelf for the freezer door, restoring lost or cracked storage space so frozen foods and small items stay organized and secure. What it does

• Replaces a cracked, broken, or missing freezer door storage bin
• Holds frozen foods, ice packs, and small containers on the freezer door
• Restores proper fit and containment to prevent items from falling when the door opens
• Fits standard freezer door openings and mounts into the door trim rails

• One freezer door bin

• Remove food and shelves from the door, then snap the old bin out of the door rail and snap the new bin in place
• Inspect door rails for damage or debris before installation to ensure a secure fit
• No tools typically required; use gentle pressure to avoid cracking the new bin
• Keep fingers clear of pinch points when seating the bin

A small canoe-shaped mounting clip used to secure tubes, wiring or small components inside the appliance, keeping lines routed and preventing rubbing or vibration for quieter, safer operation. What it does

• Secures tubing, wiring harnesses or small components to cabinet walls or frames.
• Keeps lines properly routed to prevent rubbing, chafing or pinching.
• Reduces vibration and rattling from loose parts.
• Helps maintain proper clearances that can prevent intermittent electrical contact or line wear.

• Disconnect power and shut off water before servicing.
• Verify exact clip location and orientation before removing the old clip.
• Snap into the original mounting hole or slot; do not force or bend mounting surfaces.
• Replace any damaged mounting posts or surrounding hardware to ensure a secure fit.

This condenser strap assembly secures the condenser coil to the refrigerator chassis, helping keep the coil stable and reduce vibration or contact with nearby components during operation. It's a simple replacement that restores proper condenser mounting. What it does:

• Holds the condenser coil firmly in place to prevent movement or rubbing against the cabinet
• Helps reduce rattling or vibration noises caused by a loose condenser
• Prevents wear or damage to the condenser from excessive movement
• Supports proper airflow clearance by maintaining correct condenser positioning

• Disconnect power to the appliance before beginning any repair.
• Use basic hand tools; support the condenser when removing and installing the strap to avoid bending the coil.
• Inspect surrounding components and fasteners; replace any damaged clips or screws as needed.

This metal condenser strap secures the condenser coil to the refrigerator frame, helping keep the coil stable and properly positioned for efficient operation. Replaces a worn or damaged strap to stop movement and rattling. What it does:

• Holds the condenser coil or assembly firmly in place to prevent vibration and noise
• Keeps the condenser aligned so airflow and cooling performance are maintained
• Commonly replaces a bent, cracked, or missing strap that allows coil movement
• Can stop rubbing or scraping sounds caused by a loose condenser assembly

• One metal condenser strap

• Disconnect power to the appliance before starting work
• Remove access panels as needed; support the condenser/coils while swapping the strap
• Use appropriate hand tools; avoid over-tightening fasteners which can bend the strap
• Watch for sharp sheet-metal edges and wear gloves and eye protection

This outer corner cap replaces a broken or missing plastic trim piece on the appliance door, restoring a finished look and protecting the edge from further damage. Designed as a direct-fit cosmetic/trim component. What it does:

• Covers and protects the appliance door corner from chips, dings, and everyday wear.
• Restores a flush, finished appearance where the original corner trim is cracked or missing.
• Helps prevent moisture and debris from collecting in the corner joint.
• Common symptom: visible cracked, loose, or missing corner trim on the door edge.

• High-level replacement — usually snaps into place or secures with a small screw; remove any old, damaged trim before installing.
• Disconnect power or follow manufacturer safety guidance if working near electrical components.
• Use a non-marring tool to avoid scratching adjacent surfaces when prying out the old cap.
• Warming the new cap slightly can ease installation; do not force parts.