Gte18ithbb Parts

Fiberglass insulation sleeve for refrigerator tubing. Replaces worn, damaged, or missing sleeves that protect refrigerant lines and reduce noise.

Replacement door stop for top-mount refrigerators. Installs on the door or cabinet to prevent overextension. Replace if cracked, broken, or missing.

Replace a cracked or broken console housing that exposes control components. This housing secures the control board and restores a clean appearance.

Front left wheel assembly for top-mount refrigerators. Replaces broken or worn mobility wheels that allow your refrigerator to roll smoothly for cleaning.

Black plastic door stop that mounts on your refrigerator to prevent the door from opening too far. Replace if cracked, broken, or missing to protect hinges.

Black freezer door stop that cushions and limits door travel. Replaces worn, cracked, or missing stops to protect hinges and cabinet edges.

Secures and guides your refrigerator door for smooth operation. Replace when door sags, misaligns, or fails to seal properly. Confirm fit with your model.

Full-width cantilever glass shelf for refrigerator storage. Installs in main compartment. Replace if cracked, broken, or missing to restore support.

Fixes refrigerator freezer frost buildup or warm temperatures due to defrost system failure. This wiring harness restores defrost cycle operation.

Refrigerator not cooling or defrosting? This evaporator wiring harness restores electrical connections behind the coil for reliable defrost cycles.

Replacement freezer door assembly for refrigerators. Installs as the complete outer freezer door. Needed when original is cracked, damaged, or worn.

A small canoe-shaped mounting clip used to secure tubes, wiring or small components inside the appliance, keeping lines routed and preventing rubbing or vibration for quieter, safer operation. What it does

• Secures tubing, wiring harnesses or small components to cabinet walls or frames.
• Keeps lines properly routed to prevent rubbing, chafing or pinching.
• Reduces vibration and rattling from loose parts.
• Helps maintain proper clearances that can prevent intermittent electrical contact or line wear.

• Disconnect power and shut off water before servicing.
• Verify exact clip location and orientation before removing the old clip.
• Snap into the original mounting hole or slot; do not force or bend mounting surfaces.
• Replace any damaged mounting posts or surrounding hardware to ensure a secure fit.

This condenser strap assembly secures the condenser coil to the refrigerator chassis, helping keep the coil stable and reduce vibration or contact with nearby components during operation. It's a simple replacement that restores proper condenser mounting. What it does:

• Holds the condenser coil firmly in place to prevent movement or rubbing against the cabinet
• Helps reduce rattling or vibration noises caused by a loose condenser
• Prevents wear or damage to the condenser from excessive movement
• Supports proper airflow clearance by maintaining correct condenser positioning

• Disconnect power to the appliance before beginning any repair.
• Use basic hand tools; support the condenser when removing and installing the strap to avoid bending the coil.
• Inspect surrounding components and fasteners; replace any damaged clips or screws as needed.

Retainer clip secures components inside your refrigerator. Replace if broken, loose, or missing to prevent rattling and ensure proper part alignment.

This nozzle control foam is a soft sealing pad that fits around the refrigerator dispenser nozzle to help cushion the nozzle and maintain a tight seal at the dispenser opening. It keeps the dispenser area neater and helps reduce splashes and drafts. What it does:

• Seals the gap around the dispenser nozzle to limit water drips and air infiltration
• Cushions and stabilizes the nozzle to reduce movement and wear
• Helps keep the dispenser opening cleaner by blocking debris entry
• Can reduce minor splatter and improve dispenser appearance

• Disconnect power and shut off the water supply before servicing the dispenser area
• Remove the dispenser bezel or outer trim to access the nozzle per your model's service instructions
• Press the foam into the nozzle cavity until it seats evenly; do not stretch or tear the foam
• Use only manufacturer-approved fasteners or clips; avoid adhesives unless your service manual specifies