Gts18gthww Parts

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

Secures trim and panels in your refrigerator. Replace when broken clips cause loose parts or rattling. Verify fit with your model number.

Fixes uneven cooling or frost buildup caused by a misaligned defrost heater. This holder assembly secures the element in place. 15-minute repair.

This condenser support is the replacement mounting bracket that secures the refrigerator condenser coil and helps keep the unit stable behind the lower access panel. It restores proper condenser positioning for reliable cooling performance. What it does:

• Holds the condenser coil in the correct position to prevent contact with other components
• Reduces vibration and rattling from a loose condenser assembly
• Helps maintain proper airflow behind the cabinet when installed correctly
• Can prevent wear to nearby components caused by a displaced condenser

• Disconnect power before servicing and work with the appliance unplugged to avoid shock
• Access typically requires removing the refrigerator's lower access panel or rear service panel
• Basic hand tools are usually sufficient; keep fasteners for reuse unless damaged
• Handle edges carefully; inspect surrounding parts and wiring before reassembly

Foam gasket seals the water supply nozzle connection to prevent leaks and reduce vibration. Replace if worn or leaking. Confirm fit with your model number.

Plastic clip for bottom-mount refrigerators. Secures shelves, bins, or interior components. Replace if broken, cracked, or missing to restore stability.

White plastic corner cap that snaps onto refrigerator door corners to conceal fasteners and protect hinge areas. Replace if cracked, broken, or missing.

Protective cover for the icemaker receptacle in your freezer compartment. Prevents moisture from entering the socket when an icemaker is not installed.

Refrigerator vibrating or making loud noises? This compressor mounting clip secures the compressor to the base, reducing vibration and noise transfer.

Freezer not cooling or frost buildup? This evaporator coil absorbs heat to maintain cold temperatures. Professional repair recommended due to refrigerant.

Refrigerator not cooling properly? This condenser coil restores heat dissipation when the original is damaged or corroded. Moderate DIY install.

White plastic bumper that cushions freezer door travel and prevents slamming. Replace if cracked, broken, or missing to restore proper door positioning.

Fix intermittent or failed component operation caused by damaged wiring. This harness assembly restores proper signal and power routing in your refrigerator.

A replacement freezer door panel that restores the exterior finish and sealing surface on compatible refrigerators. Helps maintain proper cold retention and gives a clean, uniform appearance to the freezer compartment. What it does:

• Replaces a cracked, dented, or discolored freezer door panel to restore look and function
• Provides the outer surface that mates to the freezer door assembly and trim
• Helps maintain an even seal and reduces cold air loss when the door closes
• Useful when a door panel is damaged by impact or cosmetic wear

• One white freezer door panel

• Basic door trim removal and reassembly required; retain all fasteners and clips for reuse if undamaged
• Disconnect power to the appliance before starting work to avoid electrical hazards
• Handle panel carefully to avoid scratching the finish; use protective gloves and a soft surface
• If the door contains internal components (liners, insulation, hinges), reattach per manufacturer instructions

This is the complete freezer door assembly, including the outer door panel and inner liner, designed for the freezer compartment of a side-by-side or top-freezer refrigerator. It provides an insulated, sealed closure that maintains proper freezer temperatures. Replace this assembly if the door panel is dented, cracked, or warped, or if the door is no longer sealing properly and causing frost buildup or temperature issues.