Gtw330askww Parts

This 6-32 machine flat-head hinge lid screw secures the lid hinge on compatible GE appliances, restoring proper lid alignment and smooth opening and closing. A simple replacement that addresses loose or rattling lids. What it does

• Fastens the lid hinge to the cabinet or hinge assembly
• Keeps the lid aligned for smooth opening and closing
• Helps stop lid wobble, rattling or uneven seating
• Replaces worn, stripped, or missing hinge screws

• One 6-32 machine flat-head hinge screw

• Turn power off and unplug appliance before servicing
• Use the correct-size screwdriver or nut driver to avoid stripping the head
• Thread screw in by hand to start, then tighten snugly—do not over-torque
• Check hinge alignment and lid operation after installation

This white control panel is the exterior trim piece that houses the range/oven user interface and secures the control board and buttons. It restores the appliance's finished appearance and provides a stable mounting surface for the controls. What it does:

• Replaces cracked, warped, scratched or faded control panel trim to restore appearance
• Provides the mounting surface and bezel for the control board, keypad and buttons
• Helps eliminate loose or misaligned buttons and trim that can interfere with normal use
• Maintains proper alignment of the control assembly and protects underlying components

• One white control panel

• Disconnect power to the appliance before starting any work
• Basic hand tools are typically required; follow OEM service instructions for disassembly
• Handle carefully to avoid scratching the finish and to protect attached electronics

This control board shield protects the appliance's electronic control board from debris, heat, and accidental contact to help maintain reliable operation. It's a direct-fit replacement designed to restore proper protection for the control electronics. What it does:

• Covers and shields the electronic control board from dust, moisture splash, and physical contact
• Helps reduce risk of short circuits caused by loose debris or small objects
• Preserves board components from incidental heat exposure and wear
• Commonly replaced when the old shield is cracked, broken, or missing

• One control board shield

• Disconnect power before servicing to avoid shock or damage to electronics
• Handle shield and control board carefully to avoid bending tabs or damaging connectors
• Reuse original fasteners if undamaged; replace any broken clips or screws

This tub cover is a replacement interior cover that protects the washer tub assembly and helps maintain proper water flow and cleaning performance. It restores the tub's sealing and shielding where the original cover is cracked or missing. What it does:

• Protects the tub assembly and internal components from debris and direct spray
• Helps maintain proper water flow patterns for consistent cleaning
• Reduces the chance of parts rubbing against the tub and causing noise or damage
• Commonly replaced when the cover is cracked, warped, or shows visible wear

• Disconnect power to the appliance before beginning any work
• Turn off water supply and drain the tub if applicable
• Basic hand tools required; follow OEM disassembly steps for access
• Handle carefully—edges may be sharp and proper alignment is required for a correct fit

This backsplash assembly kit replaces a damaged or missing backsplash on compatible ranges and cooktops, restoring the finished back area and helping protect the wall behind the appliance. Fits white finish for a factory look. What it does

• Replaces cracked, bent, or missing backsplash panels and trim that leave the back of the range exposed
• Restores the appliance's finished appearance and helps block grease and splatter from reaching the wall
• Provides the mounting surface and trim that align with controls or rear components on compatible models
• Helps prevent drafts and keeps wiring and components behind the range covered

• Disconnect power to the appliance before starting any work; follow all safety guidelines
• Handle edges carefully — metal/trim can be sharp
• Installation may require basic hand tools and alignment of mounting points; have a second person available for lifting larger panels

The Ground Screw is an OEM part for GE dryers. It ensures proper grounding and electrical safety for your dryer. This screw securely connects the ground wire to the dryer chassis, providing a path for electrical current to safely discharge in the event of a fault or power surge.

A bad Ground Screw can lead to electrical issues and potential safety hazards. Causes of a bad Ground Screw can include corrosion, loose connections, or damage due to accidental mishandling or improper installation.

Symptoms of a bad Ground Screw include:

• Intermittent dryer operation
• Visible signs of damage or deterioration on the screw or ground wire
• Tripped circuit breakers or blown fuses

Replace your faulty or damaged Ground Screw with this genuine OEM GE part to ensure proper grounding and electrical safety for your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This dual harness connector is a direct-fit replacement plug that secures two wire harnesses to restore a reliable electrical connection. It helps eliminate loose or intermittent wiring connections for affected appliance circuits. What it does:

• Provides a secure, snap-fit connection between two wire harnesses
• Restores continuity to circuits that show intermittent power, no power, or erratic operation
• Holds wiring in proper alignment to prevent accidental disconnection
• Used where a dual-wire plug mates to a control, switch, or component

• One dual harness connector

• Always disconnect power to the appliance before servicing
• Inspect wire ends and terminals for damage; replace or repair wiring if needed
• Use appropriate tools to seat the connector fully; do not force or bend terminals

This left backsplash support is the metal bracket that secures the range/oven backsplash and helps keep the control panel and rear trim stable. It restores proper alignment and reduces movement of the upper back assembly. What it does

• Provides structural support for the left side of the backsplash and control panel area
• Keeps the backsplash and rear trim aligned to prevent wobble or sagging
• Helps stop vibration or rattling coming from the upper rear of the appliance
• Replaces a bent, broken, or missing left support bracket

• One left backsplash support bracket

• Disconnect power to the appliance before starting any repair
• You may need to remove the range top, control panel, or rear access panel to access mounting screws
• Use basic hand tools; keep fasteners for reuse and note their original locations
• If you see additional damaged or missing fasteners or trim, replace them as needed for a secure fit

This rear control panel replaces the damaged or worn console panel that mounts behind the range/oven controls, restoring a secure mounting surface and proper protection for control wiring and components. Fits styles that use a rear-mounted control console. What it does

• Provides the mounting surface and enclosure for control switches, touchpads, and indicator lights.
• Protects internal wiring and control components from heat, debris, and accidental contact.
• Restores proper alignment for knobs, buttons, and display modules when the original panel is bent, cracked, or missing.
• Helps eliminate loose or vibrating controls and can resolve cosmetic damage to the console area.

• One rear control panel.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Removal typically requires taking off back access panels and disconnecting any attached control cables or grounding screws; keep hardware for reinstallation.
• Handle edges and sheet-metal openings with care; wear gloves and eye protection to avoid cuts.
• Note wiring locations and take photos before disconnecting for correct reassembly.

A molded metal support bracket that holds the right side of the oven/range backsplash assembly in place, restoring secure alignment and preventing sagging or gaps behind the control area. What it does

• Secures the right side of the backsplash or backguard assembly to the range frame.
• Helps prevent the backsplash from sagging, shifting, or coming loose when using controls or cleaning.
• Can stop visible gaps that allow debris or steam behind the control panel.
• Works with the existing backsplash components and mounting hardware to maintain proper fit.

• One right backsplash support bracket.

• Disconnect power to the appliance before attempting any service.
• Access may require removing the cooktop, control panel, or top trim.
• Use appropriate hand tools; keep track of fasteners and any clips removed.
• If the backsplash or adjacent parts are damaged, inspect related fasteners and supports for wear before reassembly.