Gtw485asjw3s Parts

This molded wire tie standoff provides a secure anchor point for a cable tie to hold wiring and harnesses away from moving parts and hot or sharp surfaces, helping reduce wear and electrical risk. Fits common HVAC and appliance wiring panels. What it does:

• Anchors wire ties to the appliance cabinet or chassis so harnesses stay routed and secured
• Prevents wires from rubbing on sharp edges, hot components or moving parts
• Helps stop intermittent electrical issues from loose or vibrating connections
• Reduces noise from loose wiring that can vibrate during operation

• One wire tie standoff

• Disconnect power before servicing the appliance to avoid shock or damage
• Mount in the original standoff hole or approved panel location; secure a cable tie through the top loop to hold the harness
• Use the correct fastener or snap method for your model—do not force or overtighten
• If routing or attaching multiple wires, verify clearance from heating elements and moving parts

This belt protector is a replacement cover that shields the dryer drive belt and nearby components from damage, helping maintain smooth drum rotation and prevent premature belt wear. What it does:

• Covers and protects the dryer drive belt from contact with the cabinet and foreign objects
• Helps prevent belt fraying and rubbing that can cause noise or reduced performance
• Keeps lint and debris away from the belt path to reduce overheating risk
• Supports proper belt routing for consistent drum movement

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer top or rear panel—use basic hand tools
• Inspect the drive belt and idler for wear while the protector is off; replace if damaged

This left-side wireform hinge secures and guides a top lid, restoring smooth opening and stable closure for affected appliances. It replaces a bent or worn hinge to reduce sagging, uneven gaps, and noisy or sticky lid movement. What it does

• Supports the lid on the left side and keeps it aligned during open/close cycles
• Restores smooth pivoting when the original hinge is bent, stretched, or broken
• Helps eliminate lid sag, uneven gaps, or rubbing against the cabinet
• Reduces rattling or binding caused by a damaged wireform hinge

• Disconnect power to the appliance before starting repairs to avoid injury
• Basic hand tools typically required; remove any trim or screws securing the old hinge
• Align the new hinge carefully and test the lid travel before fully tightening fasteners

This 6-32 machine flat-head hinge lid screw secures the lid hinge on compatible GE appliances, restoring proper lid alignment and smooth opening and closing. A simple replacement that addresses loose or rattling lids. What it does

• Fastens the lid hinge to the cabinet or hinge assembly
• Keeps the lid aligned for smooth opening and closing
• Helps stop lid wobble, rattling or uneven seating
• Replaces worn, stripped, or missing hinge screws

• One 6-32 machine flat-head hinge screw

• Turn power off and unplug appliance before servicing
• Use the correct-size screwdriver or nut driver to avoid stripping the head
• Thread screw in by hand to start, then tighten snugly—do not over-torque
• Check hinge alignment and lid operation after installation

This control board shield protects the appliance's electronic control board from debris, heat, and accidental contact to help maintain reliable operation. It's a direct-fit replacement designed to restore proper protection for the control electronics. What it does:

• Covers and shields the electronic control board from dust, moisture splash, and physical contact
• Helps reduce risk of short circuits caused by loose debris or small objects
• Preserves board components from incidental heat exposure and wear
• Commonly replaced when the old shield is cracked, broken, or missing

• One control board shield

• Disconnect power before servicing to avoid shock or damage to electronics
• Handle shield and control board carefully to avoid bending tabs or damaging connectors
• Reuse original fasteners if undamaged; replace any broken clips or screws

This hex-head machine screw secures appliance panels and internal components where a 5/16-24 x 1 inch fastener is required. Durable replacement for stripped or missing screws to restore safe assembly and reduce vibration. What it does:

• Fastens panels, brackets, and assemblies with a 5/16-24 machine thread.
• Replaces worn, stripped, or missing screws that can cause rattling or loose parts.
• Provides a secure, threaded connection for metal-to-metal or tapped-hole repairs.
• Matches OEM thread and length to maintain proper fit and alignment.

• Disconnect power and unplug the appliance before servicing.
• Use the correct hex driver or socket to avoid rounding the head.
• Thread into matching 5/16-24 tapped holes; do not force into incorrect thread sizes.
• Tighten snugly but avoid over-torquing to prevent stripping the tapped hole.

This decorative badge is the exterior emblem that mounts to the appliance cabinet or door to restore factory appearance and identification. It replaces a missing, faded, cracked, or detached emblem for a clean, finished look. What it does:

• Replaces a worn, damaged, or missing appliance emblem
• Restores original exterior appearance and branding visual
• Prevents loose badges from catching on clothing or edges
• Designed to match OEM fit and finish for a seamless look

• Typically installs on the appliance front using clips or adhesive
• Clean and dry the mounting surface before installing to ensure proper adhesion or fit
• Avoid excessive force when seating the badge to prevent damaging trim or clips
• Wear gloves to protect finish and follow general appliance-safety practices

This thermistor clip secures a refrigerator/freezer temperature sensor in the correct position so the control can read accurate temperatures and keep the appliance cycling properly. Simple replacement of a damaged clip restores proper sensor placement. What it does:

• Holds the refrigerator thermistor/sensor against the evaporator tube or cabinet to ensure stable temperature readings
• Prevents the sensor from shifting or falling away, which can cause incorrect temperature control or erratic cooling
• Keeps wiring routed and protected from contact with moving or hot components
• Small, durable clip designed for a snug fit without damaging the sensor

• Disconnect power before servicing to reduce risk of shock or injury
• Handle the thermistor sensor carefully; avoid kinking or pulling the sensor leads
• Clip the sensor gently into place so it contacts the evaporator tube or designated mounting point without crushing the sensor
• After installation, restore power and verify proper temperature control and normal compressor/defrost cycles

This dual harness connector is a direct-fit replacement plug that secures two wire harnesses to restore a reliable electrical connection. It helps eliminate loose or intermittent wiring connections for affected appliance circuits. What it does:

• Provides a secure, snap-fit connection between two wire harnesses
• Restores continuity to circuits that show intermittent power, no power, or erratic operation
• Holds wiring in proper alignment to prevent accidental disconnection
• Used where a dual-wire plug mates to a control, switch, or component

• One dual harness connector

• Always disconnect power to the appliance before servicing
• Inspect wire ends and terminals for damage; replace or repair wiring if needed
• Use appropriate tools to seat the connector fully; do not force or bend terminals