Gye22gynfs Parts

This tube clamp secures flexible water tubing to its fitting in refrigerators. It helps maintain a tight seal to prevent leaks and keeps lines from slipping off under normal operating pressure.

• Holds plastic or rubber tubing firmly on a barbed fitting or nipple
• Helps prevent drips and leaks at tube connection points
• Addresses loose or disconnected water lines
• Useful when tubing slips off or won't stay seated

• Disconnect power and shut off the water supply before servicing
• Position the clamp over the tube and fitting; compress with pliers and release to lock in place
• Ensure the clamp is centered and fully seated; tug-test the tube
• Restore water and power; check all connections for leaks

This hinge cap is the small trim piece that covers your refrigerator door hinge. Replacing a cracked or missing cap protects the hinge from dust and restores a clean, finished look to the door area.

• Covers and protects the door hinge hardware from dust and debris
• Restores a clean, factory-finished appearance
• Helps keep the hinge area clear for smooth door movement
• Replace when the original cap is cracked, loose, discolored, or missing

• Disconnect power before servicing the appliance
• Support the door to prevent movement while working near the hinge
• Remove the old cap; align and press the new cap onto the hinge until fully seated; reuse the original fastener if your model uses one
• Verify the cap is secure and does not rub as the door opens/closes

This Pex water line is the flexible inlet tubing that carries water to the refrigerator's dispenser and ice maker. It replaces worn or damaged tubing to restore reliable water flow and prevent leaks. What it does:

• Transfers water from the household supply to the refrigerator water valve, dispenser and ice maker
• Replaces cracked, pinholed or hardened tubing that can cause leaks
• Helps restore normal water flow when the dispenser or ice maker isn't filling
• Provides a flexible, corrosion-resistant connection for routine service or repair

• Turn off the refrigerator and shut off the home water supply before starting
• Drain any residual water from the line and relieve system pressure before disconnecting fittings
• Inspect and, if needed, replace any clamps, ferrules or valves shown in your service instructions; tighten fittings to OEM torque recommendations

This door case wiring harness connects the refrigerator door components to the main cabinet harness, restoring reliable power and signal routing for lights, dispensers, and sensors. Replaces a damaged or frayed harness to help resolve intermittent or non-working door functions. What it does:

• Transfers power and control signals between the door and cabinet wiring
• Restores operation for door-mounted lights, dispensers, and sensors affected by broken wiring
• Prevents shorts or intermittent failures caused by frayed or pinched wires
• Matches OEM routing and connector locations for a direct-replacement fit

• One door case wiring harness

• Disconnect power to the appliance before starting work to avoid shock or injury
• Handle connectors gently and route wiring per cabinet clips to avoid pinching
• Verify connector orientation and seating; secure any retained clips or screws

This right-side lower freezer drawer slide allows the freezer drawer to open and close smoothly and keeps the drawer aligned. Replaces a worn or damaged slide to restore stable drawer operation and prevent sticking or sagging. What it does:

• Guides and supports the lower freezer drawer for smooth in-and-out movement
• Replaces a broken, bent or worn right-side slide that causes the drawer to bind or drop
• Restores proper alignment so the drawer seals and closes evenly
• Works with the factory mounting points for a direct replacement

• Disconnect power to the appliance before removing drawers or service panels
• Remove the freezer drawer to access slide mounting screws; keep track of hardware
• Use appropriate hand tools; avoid forcing components to prevent damage

This 90° connector redirects a 5/16 in. line to a right-angle orientation for a neater, space-saving fit and a secure tube connection. Designed to restore proper routing where a straight join won't fit. What it does:

• Provides a right-angle connection for 5/16 in. tubing or line runs
• Keeps tubing routed close to the appliance to avoid kinks and strain
• Helps maintain a sealed joint to reduce risk of leaks at the turn
• Used where space constraints require a compact, 90° tube connection

• Shut off the water supply (and power if working near electrical components) before replacing the part.
• Inspect tubing ends and replace any damaged or corroded sections before installing the connector.
• Hand-start fittings, then tighten per manufacturer guidance; avoid over-tightening which may damage tubing.
• After installation, restore supply and check the joint for leaks before returning the appliance to normal use.

Size: 8 - 18 ab.

This is a replacement round-head screw sized 10-24 x 5/8 in. It secures trim, panels, and internal components so parts stay aligned and appliances run quietly and safely. What it does

• Fastens panels, brackets, and trim pieces in place
• Prevents loose parts that can rattle or cause misalignment
• Replaces missing or stripped screws to restore secure mounting
• Works where a 10-24 x 5/8 round-head screw is required

• Disconnect power before servicing the appliance
• Use the proper screwdriver or nut driver to avoid stripping the head
• Align parts before tightening and thread gently to avoid cross-threading
• Do not over-tighten; stop when snug to prevent panel distortion

This clutch coupling connects the washer motor/clutch to the agitator so the tub agitates properly during the wash cycle. Replaces a worn or broken coupling to restore normal agitation and reduce slipping or grinding. What it does:

• Transfers motor/clutch rotation to the agitator so clothes move during wash cycles.
• Commonly used when the washer spins but does not agitate or when agitation is weak.
• Helps eliminate slipping, grinding, or unusual noise from a failing coupling.
• Works as the mechanical link between the drive system and agitator assembly.

• One clutch coupling as pictured and specified by the OEM.

• Disconnect power and water supply before starting any repair.
• Basic mechanical skills and common hand tools required; follow OEM disassembly steps for safe access.
• Inspect related parts (agitator, drive shaft, clutch) for wear and replace as needed.

This E-clip is a small metal retaining ring that secures shafts, pins, and other round components in appliance assemblies, helping keep moving parts properly seated and preventing unwanted disassembly. What it does:

• Clips onto a shaft or pin to hold components in place and maintain alignment
• Prevents parts from sliding off during operation, reducing noise and wear
• Common symptom: loose or rattling components where a retaining clip is missing or damaged
• Common symptom: assembly falling apart or not engaging correctly due to a failed clip

• One E-clip

• Small part — use needle-nose pliers or snap-ring pliers to install and keep fingers clear
• Disconnect power and/or water to the appliance before servicing to avoid injury
• Wear safety glasses to protect against the clip snapping during installation

This LED light shield protects and diffuses the refrigerator's LED lighting, restoring even illumination and preventing direct exposure to the lamp. Replace a cracked, yellowed, or missing shield to improve light distribution and appearance. What it does:

• Covers and protects the LED light assembly from damage and debris.
• Diffuses LED output for softer, more even interior lighting.
• Replace if the shield is cracked, broken, warped, or discolored.
• Helps prevent direct glare from exposed LEDs for safer visibility.

• One LED light shield / cover.

• Disconnect power to the appliance before starting any work.
• Handle the shield carefully—plastic can crack; avoid overtightening fasteners.
• Install by aligning with existing mounting points or clips; do not force into place.
• Inspect the LED module and wiring.

This trough drain collects and channels defrost water from the freezer evaporator to the drain tube, helping prevent pooled water and icing in the freezer compartment. Designed to match OEM fit and function for a direct replacement. What it does

• Captures defrost meltwater from the evaporator area and directs it to the drain system
• Helps prevent water pooling and ice buildup around the evaporator and freezer floor
• Restores normal defrost drainage when original trough is cracked, warped, or clogged
• Works with the freezer's drain heater and drain tube to keep water flowing during defrost cycles

• One trough drain

• Remove power to the appliance before accessing the evaporator/freezer cavity
• Replacement may require partial disassembly of interior liners, shelves or evaporator cover; follow OEM service instructions
• Inspect and clear the drain tube and drain heater when replacing the trough to ensure full system function

This left-side freezer bracket slide secures and guides a freezer shelf or drawer, restoring stable support and smooth movement. Replaces a broken or worn slide to keep freezer shelving aligned and functioning. What it does:

• Supports the left side of a freezer shelf/drawer and guides sliding motion
• Prevents shelf sagging, misalignment, or catching when opening/closing
• Replaces cracked, bent, or missing brackets that allow shelves to drop
• Helps restore even weight distribution for safe storage

• Disconnect power before servicing and work with the freezer empty and temperature stabilized
• Remove freezer drawers/shelves for access; keep track of fasteners
• Use basic hand tools; align bracket before tightening to avoid binding

This silicon controlled rectifier (SCR) switches and regulates power to heating or motor circuits, helping the appliance control temperature and run cycles reliably. It's a direct-fit electronic switching component used in a variety of control systems. What it does:

• Acts as an electronic switch to regulate AC power to heating elements or motors
• Helps control temperature output and maintain consistent cycle performance
• Can prevent unwanted continuous current flow when functioning properly
• Commonly replaced when ovens, ranges, or dryers fail to heat or cycle correctly

• One silicon controlled rectifier (SCR) as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the SCR by its body; avoid touching terminals and static-sensitive areas
• Verify proper orientation and secure mounting; follow OEM wiring and torque practices

This PEX water line provides a flexible, durable water supply connection for compatible appliances, restoring proper water delivery for dispensers and ice makers. It resists kinking and corrosion for reliable flow. What it does:

• Carries potable water from the household supply to the appliance water valve or dispenser.
• Restores water flow when the original line is cracked, pinholed, or damaged.
• Helps prevent leaks compared with brittle or corroded rigid tubing.
• Supports normal dispenser and ice maker operation when installed correctly.

• One PEX water line.

• Turn off and disconnect the water supply and power before starting work.
• Drain remaining water from the line and fittings to avoid spills.
• Use the correct fittings and follow manufacturer torque recommendations; hand-tighten then final snug with wrench.
• After installation, slowly restore water, check all connections for leaks, and test dispenser/ice maker operation.

This right-hand freezer bracket slide supports the freezer drawer/drawer slide assembly, restoring proper alignment and smooth operation of the drawer. Replace a broken or worn bracket to stop sagging, binding, or falling drawers. What it does

• Secures and guides the freezer drawer slide on the right side
• Restores smooth sliding and proper drawer alignment
• Prevents the drawer from binding, sagging, or coming off the track
• Helps maintain proper support for heavy or loaded drawers

• One right-hand freezer bracket slide

• Disconnect power to the appliance before starting work
• Empty the drawer and remove any obstructing components per service instructions
• Use basic hand tools; ensure the bracket is oriented to match the opposite side
• Check for related damaged slide hardware and replace as needed