Hbl5450uc/6 Parts

This factory fixing kit provides the mounting hardware needed to secure the applicable component or panel on your appliance. Replacing worn or missing fasteners restores proper alignment and a solid, rattle-free installation.

• Secures panels, brackets, or trim to the appliance chassis or door
• Helps prevent shifting, vibration, and rattling during operation
• Restores correct alignment and fit when hardware is missing or stripped
• Useful during initial installation or when re-installing serviced parts

• Disconnect electrical power; if your appliance is plumbed, shut off water before servicing
• Follow your model's installation/service instructions for exact hardware locations and orientation
• Tighten hardware evenly; do not overtighten to avoid damaging plastic or sheet metal
• Verify alignment and smooth operation before restoring power and/or water

This door latch secures the appliance door and helps enable normal operation by keeping the door closed and latched during cycles. Replacing a worn or broken latch restores proper door engagement and reliable start/lock behavior. What it does:

• Secures the door closed so the appliance can run and complete cycles
• Engages with the strike to maintain a tight, consistent seal during operation
• Helps the control detect a closed/locked door and permit cycle start
• Commonly replaced when the door won't stay closed, won't lock, or the unit won't start

• One replacement door latch

• Disconnect power and water before beginning any repair
• Access may require removing the inner door panel or front trim—keep fasteners organized
• Verify alignment of the latch and strike before reassembly to ensure proper engagement
• If the latch has electrical connectors, reconnect securely and avoid pinching wires

This heating element restores proper water temperature and drying performance in your dishwasher. When the original fails, cycles may run long and dishes can come out wet; replacing it brings back consistent, efficient cleaning results. What it does:

• Heats wash and rinse water to help dissolve detergent and remove soils
• Raises final rinse temperature to improve drying performance
• Works with the control and sensors to maintain target temperatures
• Common symptoms include water not heating, poor drying, extended cycles, or a heating-related fault

• 1 heating element

• Disconnect power at the breaker and shut off water before servicing
• Pull the dishwasher and/or remove the toe panel as needed to access the heater wiring and mounts
• Note wire positions and make secure, clean terminal connections
• After reassembly, run a test cycle and inspect for leaks and proper heating

This socket is an electrical connector used to join wiring or plug-in components, restoring a secure connection for reliable appliance operation. It replaces a worn or damaged socket to help prevent intermittent power or component failure. What it does:

• Provides a secure electrical connection between wiring and the appliance component
• Restores proper contact when a loose, corroded, or broken socket causes intermittent operation
• Helps prevent arcing or poor connections that can lead to component failure
• Used where a plug-in or push-fit electrical connection is required

• One socket

• Disconnect power to the appliance before inspecting or replacing the socket
• Replace only with the exact socket type specified for your appliance

This grille for pan is a replacement trim piece that restores proper airflow and appearance around the appliance pan. It helps keep the pan area protected and looking finished after repair. What it does:

• Covers and ventilates the pan opening to help direct airflow and prevent debris entry
• Replaces a cracked, warped, or missing grille to restore fit and finish
• Helps eliminate rattling or rubbing caused by a damaged trim piece
• Matches OEM fit so it installs cleanly with the original mounting points

• Install requires removal of the surrounding trim or access panel; follow your appliance manual
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• Disconnect power to the appliance before working in the service area
• Replace damaged clips or screws with OEM fasteners for secure fit

This metal mounting bracket secures internal components and panels to restore proper alignment and reduce rattling. It's a straightforward replacement part that helps keep appliance panels and assemblies firmly in place for reliable operation. What it does:

• Provides a secure attachment point for panels or internal assemblies to prevent movement and vibration
• Helps correct alignment issues that can cause rubbing, gaps, or noise
• Restores the original fit where a bent, cracked, or missing bracket caused loose parts
• Works with the appliance's existing fasteners and mounting points

• Remove power and, if applicable, disconnect the appliance from water before beginning work
• Use the factory fasteners or OEM replacement screws to secure the bracket in the original location
• Verify alignment of the attached panel or assembly before fully tightening fasteners

This cap is a direct-fit replacement closure used to protect and seal an exposed opening or component on compatible Bosch appliances, preventing dirt, moisture and damage for reliable operation. What it does:

• Covers and seals an exposed port or fastener to keep contaminants out
• Protects internal components from moisture and debris that can cause malfunctions
• Replaces cracked, warped or missing caps that allow leaks or debris intrusion
• Restores proper fit and appearance where a damaged cap leaves an opening

• Disconnect appliance power and water supply before starting any repair
• Verify the cap matches the damaged/original part before installation
• Press or snap the cap into place until fully seated; do not force or pry
• Inspect mating surfaces for damage or debris and clean before installing

This is a small OEM retainer clip designed to secure wiring, hoses or small components inside the appliance to prevent rubbing, chafing and noise. It helps keep internal parts in their intended position for reliable operation. What it does:

• Holds wiring harnesses or small hoses in place to prevent contact with moving or hot parts
• Reduces rattling and vibration-related noise by keeping components secured
• Prevents wear and potential damage caused by loose or rubbing wires and hoses
• Helps maintain proper routing so related components continue to function as intended

• Disconnect power and water before accessing internal components
• Inspect surrounding area and replace any damaged or worn clips with the same style
• Press clip into the designated mounting slot or panel until it seats securely; ensure harness/hose is routed correctly
• Use caution around sharp sheet metal; wear gloves and follow appliance manufacturer instructions

This facia panel is the exterior trim that covers and protects your appliance's control area, restoring a clean, finished look and shielding buttons and electronics from spills and wear. It's a direct-fit replacement designed for an exact aesthetic match. What it does:

• Covers and protects the control buttons and display from moisture, grease, and everyday wear
• Restores the appliance's appearance when the original facia is cracked, faded, or damaged
• Provides the visible surface for button labels and indicators so controls remain easy to read and use
• Helps keep underlying electronic components free from debris that can affect operation

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Handle the trim carefully to avoid scratching the finish; use soft tools where needed
• Installation typically requires removing the outer door or control assembly

This support mounting bracket secures internal components to the appliance frame, restoring proper alignment and stable operation. It replaces a worn, broken, or loose support to help reduce rattling and prevent component sag. What it does:

• Provides a secure mounting point for internal parts and assemblies
• Re-establishes correct alignment when a bracket is bent or broken
• Helps reduce vibration and rattling caused by loose or damaged supports
• Commonly replaced when a component shifts, rubs, or no longer sits flush

• Disconnect power and water before starting any repair.
• Basic hand tools are typically required; follow OEM service instructions for disassembly/reassembly.
• Inspect adjacent fasteners and clips; replace any that are damaged to ensure a secure fit.

This trim plate is a decorative panel that restores the finished look of the appliance opening and helps cover gaps around the control or access area. It provides a clean, factory appearance and prevents dirt from collecting in the seam. What it does:

• Covers and finishes the edge of an opening or control area for a seamless appearance
• Helps keep crumbs, dust and spills from entering gaps around the appliance face
• Replaces bent, scratched or discolored trim that affects the appliance look
• Restores proper alignment where a damaged trim creates visible gaps

• One trim plate

• Disconnect power to the appliance before attempting removal or installation
• Handle carefully to avoid scratching the finished surface; use soft gloves if available
• Retain any mounting screws or clips from the original trim and reuse if appropriate

This mounting bracket secures appliance panels or components in place to restore proper fit and stable operation. A simple replacement when a broken or bent bracket causes rattling, misalignment, or loose panels. What it does

• Provides structural support to hold panels, trim, or assemblies in position
• Prevents rattling and vibration from a loose or damaged bracket
• Restores proper alignment of the attached component for normal operation
• Can fail from bending, cracking, or fastener loss, leading to gaps or movement

• One mounting bracket

• Disconnect power and shut off water before starting any repair
• Use appropriate tools to remove fasteners; keep track of mounting screws or clips
• Inspect surrounding parts and fasteners for damage; replace any stripped hardware
• Handle sharp edges carefully and test fit before reassembly