Hbl870 Parts

This replacement grid restores a stable, properly fitting surface in your appliance. It supports items and allows airflow or drainage as designed, helping maintain safe, reliable performance.

• Provides a rigid, open-grid surface for support and spacing
• Helps maintain proper airflow or drainage through the area
• Replace if bent, cracked, missing, or excessively worn
• Common signs include poor fit, wobbling, tipping items, or visible damage

• Disconnect power and, if applicable, shut off gas/water before service
• Allow all hot surfaces to cool completely
• Remove the old grid and clean the seating/mating points
• Set the new grid securely in place and verify a stable, level fit

This replacement screw secures appliance panels and components at their mounting points. Swap in a new screw to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded.

• Fastens the designated panel, bracket, or component in place
• Replaces a missing, stripped, or rusted screw
• Helps address loose panels, gaps, rattling, or misalignment at the mounting point
• Maintains proper assembly integrity after service or vibration

• Disconnect power; shut off water supply if working near plumbing
• Match to the removed fastener and replace one at a time to preserve alignment
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly and avoid overtightening, especially into plastic or thin sheet metal

Temperature regulator that monitors and controls an appliance's operating temperature to help maintain set points and stable performance. Replacing a faulty regulator can restore consistent temperature behavior and reliable operation. What it does:

• Senses and regulates temperature to maintain the appliance's set point.
• Signals the appliance's heating or cooling system to cycle on and off as needed.
• Common symptom: appliance temperature is too high or too low.
• Common symptom: temperature fluctuates or fails to stabilize.
• Common symptom: heating/cooling runs continuously or not at all.

• Disconnect power to the appliance before starting any service.
• Handle electrical connections and terminals with care; note wire locations before removal.
• Follow the appliance service manual or wiring diagram for proper placement and orientation.

This replacement screw secures appliance panels, brackets, or internal components. Swap out missing, stripped, or corroded hardware to restore a tight, rattle-free fit and keep assemblies properly aligned for reliable everyday use.

• Fastens panels, brackets, or subassemblies to the appliance frame
• Helps maintain alignment and reduce vibration and rattling
• Direct replacement for a worn, corroded, or missing screw
• Typical symptoms: loose panels/handles, gaps or misalignment, rattling noises, visibly missing fastener

• Disconnect power; also shut off water or gas before servicing
• Match head/driver type and length to the original; start threads by hand to avoid cross-threading
• Reuse any original washers or spacers if present
• Tighten snugly—do not overtighten to prevent stripping threads or damaging plastic mounts

This is a push-button control switch used to complete electrical circuits for appliance functions, restoring responsive button/control operation. It replaces a worn or failed switch to help return normal control-panel behavior. What it does

• Acts as the user-input electrical contact for a specific control or function.
• Completes or breaks the circuit when pressed so the appliance will respond to commands.
• Common symptom: control or button is unresponsive or intermittent.
• Common symptom: the appliance will not start or a function will not engage when the button is pressed.

• One switch.

• Disconnect power before accessing the control panel or wiring to avoid shock.
• Handle the switch and wiring gently to avoid damaging connectors or the control board.

This genuine screw secures panels, brackets, and other components in your appliance. Replacing a missing, rusted, or stripped fastener restores a snug fit, reduces vibration, and helps keep assemblies properly aligned during daily use.

• Fastens panels, brackets, or covers to the appliance chassis
• Helps maintain alignment to reduce looseness and vibration
• Replaces missing, corroded, or stripped hardware

• Disconnect power and shut off water/gas before servicing
• Support the panel or component while removing the damaged screw
• Start the new screw by hand to avoid cross-threading, then tighten until snug—do not overtighten
• If the receiving clip or hole is stripped, repair or replace that hardware before reinstalling

This cable harness routes power and signals between the appliance control and components to restore electrical connectivity. Replaces a damaged or broken harness to help appliances power up and communicate correctly. What it does:

• Transfers power and control signals between modules, switches, and sensors
• Restores interrupted circuits caused by frayed wires or broken connectors
• Helps stop intermittent operation, loss of functions, or failure to power on when wiring is at fault
• Provides pre-terminated connector ends for plug-and-play replacement

• Disconnect power to the appliance before servicing to avoid shock or damage
• Compare connectors and wire routing to the old harness before installing
• Route harness along original clips and channels; secure to prevent chafing

This spacer sets the correct gap between mating components so the assembly aligns and operates smoothly. Replacing a worn or missing spacer restores proper fit, helps prevent rubbing, and supports consistent performance. What it does:

• Maintains specified clearance and alignment within the assembly
• Helps prevent metal-to-metal contact that can cause noise or wear
• Supports smooth movement or secure mounting where designed
• Symptoms of a failed spacer can include looseness, misalignment, scraping noises, or uneven movement

• 1 spacer

• Disconnect power (and shut off gas/water if applicable) before servicing
• Access the relevant assembly and note the spacer's orientation/position
• Replace one-for-one; seat fully and avoid overtightening fasteners
• Reassemble and test for proper alignment and smooth operation

This glass cover replaces a damaged or missing exterior glass panel to restore the appliance's appearance and protect internal components from dirt and contact. It provides a clean, finished surface that matches the original fit. What it does:

• Replaces cracked, chipped, or broken glass to improve safety and appearance
• Shields internal components from debris and everyday contact
• Restores the appliance's original exterior finish
• Helps ensure proper fit of adjacent trim and controls

• One glass cover

• Handle carefully to avoid breakage and wear protective gloves when installing
• Follow the appliance manufacturer's disassembly and reassembly instructions
• Disconnect power to the appliance before beginning any repair

This support mounting bracket secures internal components to the appliance frame, restoring proper alignment and stable operation. It replaces a worn, broken, or loose support to help reduce rattling and prevent component sag. What it does:

• Provides a secure mounting point for internal parts and assemblies
• Re-establishes correct alignment when a bracket is bent or broken
• Helps reduce vibration and rattling caused by loose or damaged supports
• Commonly replaced when a component shifts, rubs, or no longer sits flush

• Disconnect power and water before starting any repair.
• Basic hand tools are typically required; follow OEM service instructions for disassembly/reassembly.
• Inspect adjacent fasteners and clips; replace any that are damaged to ensure a secure fit.

This trim plate is a decorative panel that restores the finished look of the appliance opening and helps cover gaps around the control or access area. It provides a clean, factory appearance and prevents dirt from collecting in the seam. What it does:

• Covers and finishes the edge of an opening or control area for a seamless appearance
• Helps keep crumbs, dust and spills from entering gaps around the appliance face
• Replaces bent, scratched or discolored trim that affects the appliance look
• Restores proper alignment where a damaged trim creates visible gaps

• One trim plate

• Disconnect power to the appliance before attempting removal or installation
• Handle carefully to avoid scratching the finished surface; use soft gloves if available
• Retain any mounting screws or clips from the original trim and reuse if appropriate

This mounting bracket secures appliance panels or components in place to restore proper fit and stable operation. A simple replacement when a broken or bent bracket causes rattling, misalignment, or loose panels. What it does

• Provides structural support to hold panels, trim, or assemblies in position
• Prevents rattling and vibration from a loose or damaged bracket
• Restores proper alignment of the attached component for normal operation
• Can fail from bending, cracking, or fastener loss, leading to gaps or movement

• One mounting bracket

• Disconnect power and shut off water before starting any repair
• Use appropriate tools to remove fasteners; keep track of mounting screws or clips
• Inspect surrounding parts and fasteners for damage; replace any stripped hardware
• Handle sharp edges carefully and test fit before reassembly