Hdi80546/01 Parts

Replacement drawer front panel for ranges. Restores appearance and proper fit when the original is cracked, dented, scratched, or missing. Single drawer style.

Replacement end cap for oven door handles. Fits at either end of the handle assembly to provide a finished look and comfortable grip. Replace if cracked or missing.

Fix intermittent power or electrical faults in your range with this cable harness. Routes power and signals between control and components. Direct fit.

This replacement routing tube channels fluid inside the appliance to restore proper flow and stop leaks. It replaces a damaged, cracked, or clogged tube to help prevent water pooling and restore normal operation. What it does:

• Routes water or condensate between internal components to maintain proper drainage or flow
• Replaces cracked, split, or deteriorated tubing that can cause leaks or puddles
• Helps eliminate intermittent dripping or loss of water flow caused by blockages or holes
• Works as a direct-fit replacement when the original tubing has failed

• One replacement tube

• Disconnect power and shut off the water supply before installing
• Inspect and reuse or replace any retaining clips, clamps, or grommets as needed
• Slide tube fully into fittings and secure with appropriate clamps to prevent leaks

Fix misaligned oven components with this spacer. Restores proper gap between parts to prevent rubbing and ensure smooth operation. Simple DIY repair.

This is the inner door panel that forms the interior-facing surface of the oven door. It provides structural support for the door assembly and helps contain heat within the oven cavity. Replace this panel if it is warped, cracked, rusted, or if the oven door is not sealing properly and allowing heat to escape.

Range not heating properly or taking too long to warm up? This heating element restores proper temperature control. Moderate difficulty repair in 30-45 minutes.

This retaining washer secures a control shaft or hub to keep components in place during operation, helping restore proper control movement and prevent parts from sliding off the shaft. Simple replacement when a worn or missing retainer causes loose knobs or shifting parts. What it does:

• Fits onto a control or drive shaft to hold a knob, hub or gear in position
• Prevents axial movement that can cause loose or slipping controls
• Commonly replaced when the original washer is bent, cracked, or lost
• Works with compatible Bosch control assemblies and hubs

• One retaining washer

• Recommended for users comfortable with basic appliance disassembly; unplug appliance before starting
• Remove the control knob or panel per model instructions to access the shaft
• Press the washer into place on the shaft until fully seated; verify proper fit and control operation

Secures and supports range panels and internal assemblies. Replace if broken, bent, or missing to restore proper panel alignment and stability.

Secures the door hinge assembly to the oven cabinet frame. Replace if the original holder is cracked, broken, or missing to restore proper door alignment.

This replacement door gasket seals the dishwasher door to keep water inside the tub and help maintain wash performance. It restores a tight door seal to reduce leaks and prevent water from pooling around the appliance. What it does:

• Creates a watertight seal between the door and tub to stop leaks during cycles
• Helps prevent water from dripping onto floors and surrounding cabinetry
• Reduces steam and moisture escape that can cause odors or damage
• Restores proper door closure where worn or flattened seals allow seepage

• Disconnect power and water supply before attempting any service.
• Inspect surrounding door edges for damage and clean mounting surfaces before installing the new gasket.
• Press the gasket firmly into the door channel; some models require partial door disassembly.
• After installation, run a short cycle and check for leaks before returning the dishwasher to regular use.

Replacement control panel for electric and gas ranges. Installs on the front of the appliance. Needed when the original panel is cracked, damaged, or worn.

This set of jets replaces worn or clogged spray nozzles to help restore even water distribution for better cleaning. Designed for the dishwasher spray system, the jets direct pressurized water to remove food soils. What it does:

• Replaces damaged or clogged spray nozzles to improve spray coverage and cleaning performance
• Restores correct water flow pattern from spray arms or manifolds
• Reduces uneven washing, spots, or missed areas caused by blocked jets
• Works as a direct-fit service part where specified

• One set of replacement jets as sold

• Disconnect power and turn off the water supply before beginning any repair
• Remove the spray arm or access panel to reach the jets; small tools may be required
• Inspect surrounding gaskets and fittings; replace if cracked or leaking

Mounting screw secures internal oven components and panels. Replace if stripped, missing, or damaged during service. Essential hardware for reassembly.

This spacer is a small structural component that maintains proper clearance between oven parts. Replace if broken, missing, or worn to ensure correct spacing.

Replacement mounting screw for cooktops and ranges. Secures panels, brackets, and components. Needed when original screw is missing, stripped, or damaged.