Hei7282u/09 Parts

If your range controls aren't responding or the heating element won't turn on, this push-button switch restores reliable front-panel operation.

This sealing ring creates a watertight seal in the dishwasher pump/motor area to help prevent leaks and protect the motor assembly. It's a small but essential replacement for worn or damaged seals. What it does:

• Seals pump housing joints to stop water leaks beneath the dishwasher
• Helps maintain proper water pressure and circulation for cleaning performance
• Prevents water from reaching the motor and electronics, reducing risk of damage
• Replaces brittle, cracked, or flattened seals that commonly cause under-unit leaks

• One sealing ring

• Turn off power and water to the appliance before starting any repair
• Inspect mating surfaces and clean away debris or buildup before installing the new ring
• Lubricate the seal lightly with OEM-recommended lubricant or a thin film of water if needed to ease installation
• If multiple seals or gaskets show wear, replace them together to ensure a complete seal.

This glass front panel is the exterior replacement glass that restores the appliance's finished look and protects the underlying door and control area from scratches and wear. It fits into the door assembly to provide a clean, glossy surface. What it does:

• Replaces cracked, chipped, or heavily scratched front/door glass to restore appearance
• Protects internal components and trim from direct contact and debris
• Helps keep the door surface smooth and easy to clean
• Restores a secure fit when broken or loose glass affects the door finish

• One glass front panel

• Disconnect power to the appliance before starting any repair
• Handle glass with gloves and protective eyewear to avoid cuts
• Installation typically requires removing the door trim or bezel—follow the OEM service instructions for your model

This replacement heating element warms the air inside an electric dryer so clothes dry efficiently. Use it to restore normal heating when the dryer runs but does not produce sufficient heat. What it does:

• Heats incoming air that circulates through the dryer drum to evaporate moisture
• Commonly used when the dryer runs but produces little or no heat
• Works with the dryer's internal blower and venting to maintain normal drying cycles
• Should be checked alongside thermal fuses and thermostats when diagnosing heating problems

• One heating element assembly

• Disconnect power at the circuit breaker before accessing the heater assembly; this part can be connected to high voltage
• Replacement typically requires access to the dryer's rear or lower front panel and basic hand tools
• Avoid touching element terminals or sharp sheet-metal edges; follow OEM instructions for secure electrical and mounting connections
• If the dryer still doesn't heat after installation, test or replace related components (thermal fuse, high-limit thermostat, wiring) as needed

Oven door sealing strip creates airtight seal for efficient heating. Replace if worn, cracked, or oven struggles to maintain temperature. Verify fit.

Replace a damaged heat shield causing nearby components to overheat or melt. This protective panel restores the heat barrier on your gas range.

This part is a replacement fixing kit and is a genuine OEM part manufactured by Bosch. This part has been sourced directly from the manufacturer and is intended to repair a broken or faulty door in a variety of different oven models. This fixing kit includes both of the door hinges that are necessary for repairing the oven door. These hinges are necessary for the user to control the opening rate of the door, as well as allow the door to remain ajar at an angle. When undergoing any repair work, make sure to always disconnect the power and gas supplies from the oven. It is highly recommended that work gloves are worn to for proper protection.This is an authentic replacement part and thus is suitable for use on several different models of ovens that have been manufactured by Bosch, Thermador, Gaggenau, and some other brands.

Secures your range door and allows smooth pivoting for proper alignment and seal. Replace if your door won't close fully, sags, or doesn't seat correctly.

The Oven Light Switch is an OEM part for Bosch ranges. It engages convenient interior illumination through a single motion, allowing monitoring of baked goods without compromising temps. 

Causes of a bad oven light switch can include failures from the natural stresses of constant clicking associated with opening and closing the oven door. 

Symptoms of a bad oven light switch include:

• Dim or unresponsive lights even when the door is opened properly     
• Inability to turn lights off, leaving them burning needlessly  
• Stuck in either the on or off position without toggle functionality
• Potentially hazardous exposed live terminals under switch housings

This OEM Bosch part can also be used on Thermador and Gaggenau appliances.