Hgi8054uc Parts

This is a set of gas orifice jets used to convert a gas range from one fuel type to another, such as from natural gas to liquid propane or vice versa. Each jet is precision-drilled to meter the correct amount of gas for proper burner flame size and efficiency. You will need this kit if you are switching your gas supply type and need to recalibrate your burners to prevent improper flame height, yellow flames, or sooting.

Restore even baking when your oven heats unevenly. This convection fan blade circulates hot air for consistent cooking. Moderate DIY install.

Fixes uneven flames and weak heating on gas range burners. This surface burner head restores proper flame distribution for consistent cooking performance.

Mounting screw for ranges and cooktops. Secures panels, brackets, and components during installation. Replace if lost, stripped, or damaged.

Replacement end cap for oven door handles. Fits at either end of the handle assembly to provide a finished look and comfortable grip. Replace if cracked or missing.

Fix intermittent power or electrical faults in your range with this cable harness. Routes power and signals between control and components. Direct fit.

Replace your gas range front panel if it's cracked, discolored, or damaged. Restores the professional appearance and protects internal controls. Verify fit with your model number before ordering.

This control panel cover protects the dishwasher's electronic controls and wiring behind the front panel, helping keep moisture and debris away while restoring a clean, finished appearance. Fits the OEM location where the control board is housed. What it does:

• Shields control board and wiring from steam, splashes, and food debris
• Helps prevent intermittent faults caused by moisture exposure
• Restores a secure mounting surface for the front control assembly
• Improves appliance appearance if original cover is cracked or damaged

• Disconnect power to the appliance before starting any repair.
• Remove the outer door panel or control trim per your model's service instructions to access the cover.
• Retain any screws or clips from the original part for reinstallation unless replacements are supplied separately.

This replacement routing tube channels fluid inside the appliance to restore proper flow and stop leaks. It replaces a damaged, cracked, or clogged tube to help prevent water pooling and restore normal operation. What it does:

• Routes water or condensate between internal components to maintain proper drainage or flow
• Replaces cracked, split, or deteriorated tubing that can cause leaks or puddles
• Helps eliminate intermittent dripping or loss of water flow caused by blockages or holes
• Works as a direct-fit replacement when the original tubing has failed

• One replacement tube

• Disconnect power and shut off the water supply before installing
• Inspect and reuse or replace any retaining clips, clamps, or grommets as needed
• Slide tube fully into fittings and secure with appropriate clamps to prevent leaks

Fix misaligned oven components with this spacer. Restores proper gap between parts to prevent rubbing and ensure smooth operation. Simple DIY repair.

Range not heating properly or taking too long to warm up? This heating element restores proper temperature control. Moderate difficulty repair in 30-45 minutes.

This is the inner door panel that forms the interior-facing surface of the oven door. It provides structural support for the door assembly and helps contain heat within the oven cavity. Replace this panel if it is warped, cracked, rusted, or if the oven door is not sealing properly and allowing heat to escape.

This retaining washer secures a control shaft or hub to keep components in place during operation, helping restore proper control movement and prevent parts from sliding off the shaft. Simple replacement when a worn or missing retainer causes loose knobs or shifting parts. What it does:

• Fits onto a control or drive shaft to hold a knob, hub or gear in position
• Prevents axial movement that can cause loose or slipping controls
• Commonly replaced when the original washer is bent, cracked, or lost
• Works with compatible Bosch control assemblies and hubs

• One retaining washer

• Recommended for users comfortable with basic appliance disassembly; unplug appliance before starting
• Remove the control knob or panel per model instructions to access the shaft
• Press the washer into place on the shaft until fully seated; verify proper fit and control operation

This is a spacer insert that fits behind or between the oven door handle and the outer door panel, ensuring the handle is properly positioned and securely mounted. It helps maintain the correct gap and alignment for the door handle assembly. Replace this part if the door handle feels loose, sits unevenly, or if the original spacer is cracked or missing.