Hgi805uc/06 Parts

The Cooktop is an OEM part for Bosch gas ranges and cooktops. As the main cooking surface, the gas cooktop withstands extreme heat levels across its burners and grates on a daily basis.

Causes of cooktop deterioration stem from prolonged heat cycling combined with debris accumulation over many years. Accidental impact or surface damage from improper cleaning can also crack components prematurely.

Symptoms of a damaged cooktop include:

• Uneven or irregular burner flame patterns that waste fuel
• Hot spots creating risks of scorching or burning food
• Grates or surface areas pitted or corroded beyond repair
• Detached or damaged burner caps impacting performance

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This cable harness connects and routes power and signal lines between appliance components to restore reliable electrical connections. It replaces damaged or worn wiring to help resolve intermittent operation or loss of power to affected parts. What it does:

• Provides secure electrical connections between control boards, sensors, and motors
• Replaces frayed, broken, or corroded wiring that can cause intermittent faults
• Can stop symptoms like components not powering, erratic behavior, or communication errors
• Keeps wiring organized and routed to reduce strain and chafing

• One cable harness as shown

• Always disconnect power before starting any repair
• Match connectors and routing to the original harness; secure with existing clips or ties
• Inspect mating connectors and terminals for damage or corrosion before installation

This control panel cover protects the dishwasher's electronic controls and wiring behind the front panel, helping keep moisture and debris away while restoring a clean, finished appearance. Fits the OEM location where the control board is housed. What it does:

• Shields control board and wiring from steam, splashes, and food debris
• Helps prevent intermittent faults caused by moisture exposure
• Restores a secure mounting surface for the front control assembly
• Improves appliance appearance if original cover is cracked or damaged

• Disconnect power to the appliance before starting any repair.
• Remove the outer door panel or control trim per your model's service instructions to access the cover.
• Retain any screws or clips from the original part for reinstallation unless replacements are supplied separately.

This replacement routing tube channels fluid inside the appliance to restore proper flow and stop leaks. It replaces a damaged, cracked, or clogged tube to help prevent water pooling and restore normal operation. What it does:

• Routes water or condensate between internal components to maintain proper drainage or flow
• Replaces cracked, split, or deteriorated tubing that can cause leaks or puddles
• Helps eliminate intermittent dripping or loss of water flow caused by blockages or holes
• Works as a direct-fit replacement when the original tubing has failed

• One replacement tube

• Disconnect power and shut off the water supply before installing
• Inspect and reuse or replace any retaining clips, clamps, or grommets as needed
• Slide tube fully into fittings and secure with appropriate clamps to prevent leaks

Fix misaligned oven components with this spacer. Restores proper gap between parts to prevent rubbing and ensure smooth operation. Simple DIY repair.

Range not heating properly or taking too long to warm up? This heating element restores proper temperature control. Moderate difficulty repair in 30-45 minutes.

This is the inner door panel that forms the interior-facing surface of the oven door. It provides structural support for the door assembly and helps contain heat within the oven cavity. Replace this panel if it is warped, cracked, rusted, or if the oven door is not sealing properly and allowing heat to escape.

This retaining washer secures a control shaft or hub to keep components in place during operation, helping restore proper control movement and prevent parts from sliding off the shaft. Simple replacement when a worn or missing retainer causes loose knobs or shifting parts. What it does:

• Fits onto a control or drive shaft to hold a knob, hub or gear in position
• Prevents axial movement that can cause loose or slipping controls
• Commonly replaced when the original washer is bent, cracked, or lost
• Works with compatible Bosch control assemblies and hubs

• One retaining washer

• Recommended for users comfortable with basic appliance disassembly; unplug appliance before starting
• Remove the control knob or panel per model instructions to access the shaft
• Press the washer into place on the shaft until fully seated; verify proper fit and control operation

This is a spacer insert that fits behind or between the oven door handle and the outer door panel, ensuring the handle is properly positioned and securely mounted. It helps maintain the correct gap and alignment for the door handle assembly. Replace this part if the door handle feels loose, sits unevenly, or if the original spacer is cracked or missing.

Fix weak or uneven burner flames with this gas range pressure regulator. Controls gas flow for consistent cooking performance and safe operation.

Secures and supports range panels and internal assemblies. Replace if broken, bent, or missing to restore proper panel alignment and stability.

Secures the door hinge assembly to the oven cabinet frame. Replace if the original holder is cracked, broken, or missing to restore proper door alignment.

This replacement door gasket seals the dishwasher door to keep water inside the tub and help maintain wash performance. It restores a tight door seal to reduce leaks and prevent water from pooling around the appliance. What it does:

• Creates a watertight seal between the door and tub to stop leaks during cycles
• Helps prevent water from dripping onto floors and surrounding cabinetry
• Reduces steam and moisture escape that can cause odors or damage
• Restores proper door closure where worn or flattened seals allow seepage

• Disconnect power and water supply before attempting any service.
• Inspect surrounding door edges for damage and clean mounting surfaces before installing the new gasket.
• Press the gasket firmly into the door channel; some models require partial door disassembly.
• After installation, run a short cycle and check for leaks before returning the dishwasher to regular use.

Replacement control panel for electric and gas ranges. Installs on the front of the appliance. Needed when the original panel is cracked, damaged, or worn.

Mounting screw secures internal oven components and panels. Replace if stripped, missing, or damaged during service. Essential hardware for reassembly.