Hps15bthrww Parts

This defrost heater assembly melts frost from the evaporator during the automatic defrost cycle to keep airflow clear and temperatures stable. Replacing a failed heater helps restore consistent cooling and prevents ice buildup that blocks the freezer wall. What it does:

• Heats the evaporator coil to melt accumulated frost/ice during scheduled defrosts
• Keeps airflow paths clear to maintain proper temperatures
• Helps prevent excessive frost on the back panel or evaporator
• Common symptoms of a failed heater include heavy ice buildup, weak airflow, warmer fresh-food temps, and longer run times

• 1 defrost heater assembly

• Unplug the refrigerator before servicing; wear gloves—sheet metal edges can be sharp
• Access the heater behind the freezer's rear panel at the evaporator
• Note wire routing and connector orientation; secure the new element as originally mounted
• After installation, clear any remaining ice so airflow is restored before powering on

This temperature control thermostat regulates cabinet temperature by cycling the cooling system on and off. Replacing a faulty control restores consistent cooling performance and responsive temperature adjustments, helping protect food and prevent excessive run time.

• Senses internal temperature via a capillary sensor and opens/closes electrical contacts to power the cooling system
• Provides an adjustable setpoint through the temperature dial
• Helps maintain stable, consistent temperatures and proper cooling cycles
• Common failure symptoms: too warm or too cold, runs constantly or won't run, temperature drifts, knob unresponsive or clicking

• Disconnect power before servicing
• Photograph wire positions and dial orientation; transfer wires one at a time
• Route the capillary sensor in the original path; avoid kinks or sharp bends
• Reassemble, restore power, and allow temperatures to stabilize before final adjustment

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

Restore a tight seal on your refrigerator's fresh food compartment with this door gasket. A proper seal helps maintain temperature, limit moisture and frost, and support efficient operation when the original gasket is worn or damaged.

• Seals the perimeter of the fresh food door to prevent air leaks
• Helps stabilize internal temperature and humidity
• Reduces condensation, frost, and extended run times
• Common symptoms: torn or warped gasket, loose corners, door not sealing, condensation around the door

• Disconnect power before servicing
• Let the new gasket lay flat and warm to room temperature; use warm water or low heat from a hair dryer to relax wrinkles
• Remove the old gasket; press the new gasket fully into the door channel, seating corners first and working evenly around
• Adjust door/hinges if needed to ensure a complete seal

This bottom hinge supports the refrigerator door at the lower pivot point, keeping it aligned so it opens smoothly and seals correctly. Replace a worn hinge to restore proper closure and help maintain an airtight door seal.

• Provides the lower pivot and support for the door
• Helps maintain alignment for consistent gasket contact and smooth swing
• Wear or damage can cause door sagging, rubbing, or incomplete closure
• Misalignment can lead to air leaks and temperature fluctuations
• Clicking, grinding, or loose movement near the hinge may indicate wear

• Unplug the refrigerator; turn off water to the dispenser/ice maker
• Remove door bins/contents and support the door to prevent strain on wiring or tubing
• Remove the lower hinge cover, note shim/spacer locations, and transfer them to the new hinge
• Reinstall hardware, align the door, and ensure the gasket seals evenly all around

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This replacement clamp secures lines or components inside the refrigerator, keeping them properly routed and stable. Replacing a broken or missing clamp helps reduce vibration and prevents rubbing damage or leaks from loose tubing. What it does:

• Holds tubing or wiring harnesses securely in place inside the refrigerator
• Maintains correct routing and clearance to prevent chafing and wear
• Helps reduce vibration and rattling noises from unsecured lines
• Can help prevent drips or leaks when used to retain water tubing

• 1 clamp

• Unplug the refrigerator and, if working with water lines, shut off the water supply
• Note the original clamp orientation and routing; take a photo before removal
• Install the new clamp in the same location, securing lines without pinching or over-stressing them
• Restore power (and water if applicable) and check that lines are secure; inspect for leaks if used on water tubing

This control housing is the molded chassis that supports and positions the refrigerator's control panel components. Replacing a cracked or broken housing restores secure mounting, proper alignment, and smooth operation of the controls.

• Holds the user interface/control module and trim in the correct position
• Provides mounting points for the board, buttons, and display bezel
• Helps protect wiring connections from movement and vibration
• Common symptoms: loose or sagging control panel, broken mounting tabs, rattling near the controls, controls shifting when pressed

• Unplug the refrigerator before servicing.
• Remove any trim/cover and the screws or clips securing the housing; support the UI board and wiring.
• Transfer existing control components from the old housing to the new one.
• Ensure all tabs seat fully; tighten fasteners evenly without overtightening and avoid pinching wires.

This small donut-shaped gasket fits where specified in your refrigerator's parts diagram to create a tight seal between mating components. Replacing a worn gasket helps stop minor leaks and restore a secure fit.

• Forms a tight seal at the designated joint or fitting
• Helps prevent seepage or drips from a compromised connection
• Replaces a brittle, cracked, flattened, or missing original gasket
• Supports proper assembly alignment and a snug fit

• Unplug the refrigerator and, if servicing the water system, shut off the water supply
• Note the gasket's original placement and orientation before removal
• Clean mating surfaces; lightly moisten the new gasket to ease seating
• Reassemble without overtightening; restore power/water and check for leaks

The Actuator Air Foam is an OEM part for GE refrigerators responsible for redirecting the flow of air within the refrigerator's evaporator assembly, ensuring efficient cooling and temperature regulation.

A bad actuator air foam can be caused by normal wear and tear, exposure to moisture, or damage due to mishandling or impact. If you notice that your refrigerator is not cooling properly, or if there are temperature inconsistencies throughout the refrigerator compartment, it may indicate a problem with the actuator air foam.

Symptoms of a bad actuator air foam include:

• Inadequate cooling or freezing in certain areas of the refrigerator
• Temperature fluctuations within the refrigerator compartment
• Excessive frost or ice buildup on the evaporator coils
• Unusual noises coming from the refrigerator's cooling system

Replace your faulty actuator air foam with this genuine OEM part to restore your refrigerator. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Air Tower and Evaporator Cover Assembly is an OEM part for GE refrigerators. This multi-piece component is located inside the refrigerator compartment and manages airflow that travels through the evaporator coil area. An attractive cover protects inner workings while directing optimal temperature control.  

Symptoms of a bad air tower assembly include:  

• Audible air disturbances accompanied by inconsistent interior temperatures
• Buildup of frost or moisture collecting outside the evaporator area
• Inability of warm food to adequately cool down inside the fridge  

Causes relate to cracks developing in thermoplastic covers after years of climate cycling strains. Closed airways may become obstructed as well affecting circulation.

This GE OEM replacement restores reliable humidity management and product cooling. Its enduring construction circulates purified air for consistent food holding at proper temperatures per federal guidelines. Compatible with GE and select Kenmore side-by-side models for direct fit airflow performance.
 

This plastic water tube routes water inside your refrigerator to the dispenser and/or ice maker. Replacing a cracked, brittle, or leaking tube restores proper water flow and helps prevent leaks and water damage.

• Directs water between components such as the inlet valve, reservoir, door, dispenser, or ice maker (varies by model)
• Maintains a sealed, food-grade path to prevent leaks and air intrusion
• Damage can lead to puddles behind/under the fridge or inside the fresh food compartment
• Common symptoms: slow/no dispenser flow, ice maker not filling or making small cubes, visible cracks/kinks

• Unplug the refrigerator and shut off the household water supply; relieve line pressure at the dispenser
• Note tube routing and connection points before removal; avoid sharp bends and kinks during install
• Cut tube ends square and fully seat into compression or push-in fittings
• Restore water, check all joints for leaks, and run water to purge air from the system

This factory screw secures brackets, panels, and internal components so assemblies stay tight and aligned. Replace a missing or damaged fastener to eliminate rattles, looseness, and misaligned parts. What it does:

• Fastens components, panels, hinges, or brackets to the appliance frame
• Helps maintain proper alignment and a solid, rattle-free fit
• Replaces stripped, rusted, or missing hardware
• Can address vibration noises and loose assemblies

• Includes 1 screw

• Unplug the appliance and shut off water before servicing
• Wear gloves; sheet-metal edges can be sharp
• Start threads by hand to avoid cross-threading; use the appropriate driver
• Tighten snugly—do not overtighten to prevent stripping

This ice maker stripper is the front comb that helps release cubes from the ejector during harvest. It guides ice cleanly into the bin to reduce jams and keep ice production running smoothly. What it does

• Strips ice cubes off the ejector fingers as the ice maker cycles
• Directs cubes into the bucket, helping prevent jams and cube bridging
• Wear, cracks, or warping can cause cubes to stick, spill, or clump
• Symptoms include cubes piling at the front, clicking during harvest, or reduced/no ice

• 1 ice maker stripper

• Disconnect power and shut off water before servicing
• Remove the ice bin and access the ice maker front (remove cover if present)
• Release the old stripper (tabs/screws), align the new stripper with the ejector fingers, and seat it fully
• Reinstall cover and bin; restore power and allow a full cycle to verify operation

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

This center hinge pin is the pivot shaft for the door at the middle hinge on select refrigerators. Replacing a worn or bent pin restores proper door alignment and smooth movement to help the door close and seal correctly.

• Serves as the door's pivot on the center hinge
• Maintains correct door height and alignment
• Helps the door open and close smoothly without binding
• Common symptoms: door sagging or rubbing, squeaking, wobbling, or not closing fully/popping open

• Unplug the refrigerator and remove items from the door to reduce weight
• Support the door before removing the center hinge bracket fasteners
• Install the new pin on the center hinge; reuse original spacers/bushings in their original order
• Reassemble, then check door alignment and gasket contact; adjust the hinge as needed per your model