Hps18bthww Parts

This freezer door stop is a small plastic bumper that cushions and limits the freezer door's travel to prevent over-extension and reduce slamming. It restores proper door positioning and helps protect the cabinet edge. What it does:

• Acts as a door bumper/stop so the freezer door closes and rests correctly
• Reduces slamming and wear on the door and cabinet edge
• Helps keep the door aligned during normal opening and closing
• Can resolve symptoms like a door that over-rotates, hits the cabinet, or doesn't seat cleanly

• One white freezer door stop

• Typically installs by snapping or sliding into the hinge/cabinet mounting location; verify orientation before pressing into place
• Turn power to the appliance off only if panel removal is required; this part is non-electrical
• Use basic hand tools if needed and avoid forcing the part to prevent breakage

This wiring harness assembly connects control and electrical components to restore proper signal and power routing within the appliance. Use it to replace damaged or faulty wiring that causes intermittent or failed component operation. What it does

• Routes power and control signals between the control board and major components.
• Replaces frayed, burned, or broken wires to eliminate shorts or open circuits.
• Helps resolve symptoms like no power to components, intermittent operation, or controls that don't respond.
• Maintains correct connector fit and secure electrical connections for reliable performance.

• One wiring harness assembly as shown.

• Disconnect all power before starting any repair to avoid shock or injury.
• Compare the new harness to the original for correct connector types and lengths before installation.
• Route and secure the harness away from sharp edges, moving parts, and heat sources.

This pocket-style freezer door restores the interior door panel for compatible top- and bottom-freezer refrigerators, providing a clean, replaceable surface for shelves and bins. It helps stop drafts and keeps freezer contents secure. What it does:

• Replaces a damaged, cracked, or discolored pocket-style freezer door panel
• Restores mounting surface for door shelves and bins so they sit securely
• Helps maintain a proper door seal and reduces cold-air loss when installed
• Improves interior appearance of the freezer compartment

• Intended as a direct-replacement part; verify fit against existing part before installing
• Use basic hand tools; handle carefully to avoid scratching the finish
• Disconnect power and remove food from door area if needed for access
• If clips or fasteners are damaged, replace them with OEM replacement parts

This freezer door stop cushions and limits the door's travel to protect the hinge and cabinet edge, helping the door close smoothly and preventing over-travel damage. Fits black trim locations on compatible freezers. What it does:

• Acts as a bumper to stop the freezer door from swinging too far
• Cushions impact, reducing stress on hinge components and cabinet
• Helps the door align and close flush to maintain seal performance
• Common symptom fix: door hits cabinet, scrapes, or sits unevenly

• Remove any food/obstructions and support the door before replacing the stop
• Usually a simple snap-in or screw-on replacement; small hand tools may be required
• Inspect surrounding hinge and trim for damage when replacing
• Follow all safety precautions; unplug unit or disconnect power before performing extended service

This evaporator harness is the factory replacement wiring assembly that connects the evaporator components so the refrigerator can complete defrost cycles and circulate cold air reliably. It restores secure electrical connections behind the evaporator coil. What it does

• Routes power and signals between the evaporator fan, defrost heater and temperature sensors/thermostat.
• Helps the defrost system operate properly to prevent excessive ice buildup on the evaporator.
• Restores reliable electrical connections that can stop intermittent fan or defrost operation.
• Commonly used when connectors are corroded, wires are damaged, or the harness is melted or brittle.

• One evaporator harness wiring assembly as shown.

• Disconnect power before accessing the evaporator compartment and any wiring.
• Remove interior panels and ice/water lines as required to reach the evaporator; follow your model's service manual.
• Match connector shapes and routing; do not force connectors—replace if pins or sockets are damaged.

This condenser strap assembly secures the condenser coil to the refrigerator chassis, helping keep the coil stable and reduce vibration or contact with nearby components during operation. It's a simple replacement that restores proper condenser mounting. What it does:

• Holds the condenser coil firmly in place to prevent movement or rubbing against the cabinet
• Helps reduce rattling or vibration noises caused by a loose condenser
• Prevents wear or damage to the condenser from excessive movement
• Supports proper airflow clearance by maintaining correct condenser positioning

• Disconnect power to the appliance before beginning any repair.
• Use basic hand tools; support the condenser when removing and installing the strap to avoid bending the coil.
• Inspect surrounding components and fasteners; replace any damaged clips or screws as needed.