Jdb100aws Parts

This is a machine screw used to secure appliance panels and components where an 8-32 thread fastener is specified. It provides a reliable hold for control panels, brackets, and interior assemblies. What it does:

• Fastens panels, brackets, and small components to the appliance chassis
• Holds control assemblies and trim pieces in place
• Maintains secure connections that prevent vibration-related loosening
• Works where an 8-32 coarse-thread machine screw of short length is required

• One 8-32 x 3/8" machine screw

• Use the correct driver (Phillips or slotted) to avoid stripping the head
• Thread into metal or nut/insert; do not overtighten to prevent thread damage
• Disconnect power and remove any panels as required for safe access

Right hand side

This seal sits at the dishwasher's air/water inlet, creating a tight barrier where the inlet assembly meets the tub or door. Replacing a worn seal helps stop nuisance leaks and supports proper fill and venting performance. What it does

• Forms a watertight seal at the air/water inlet connection
• Helps prevent drips or seepage during fill and wash
• Supports correct venting to keep moisture contained inside the tub
• Common failure signs include water on the floor near the unit, dampness around the inlet/vent area, or a cracked, flattened, or brittle seal

• One air/water inlet seal

• Disconnect power and shut off water before servicing
• Access method varies by model; remove the inlet/vent cover or side panel to reach the seal
• Clean mating surfaces; seat the new seal evenly without distortion
• Reassemble and run a brief fill/wash to check for leaks

Replacement pump gasket with silicone sealing material that restores a watertight seal between the pump and housing. Helps stop leaks at the pump area and prevents water pooling under the appliance.

• Seals the pump to the housing to help prevent water leaks and drips.
• Common repair for visible water under the appliance or leaks coming from the pump area.
• Silicone sealing material provides a flexible, water-tight interface that conforms to the pump housing.
• Designed to replace the factory pump gasket for a direct fit and proper sealing.

• Disconnect power and water supply before beginning any repair.
• Remove the pump assembly to access and replace the gasket.
• Clean and dry mating surfaces before installing the new gasket; seat evenly to ensure a full seal.

This control board housing secures and protects the washer's electronic control board, keeping circuitry stable and shielded from moisture and debris for reliable operation. It fits into the console area and supports proper control panel alignment. What it does:

• Holds and protects the electronic control board inside the console from impact, dust and moisture.
• Keeps the control board properly positioned for reliable electrical connections.
• Helps prevent control panel wobble or misalignment that can cause button or dial issues.
• Commonly replaced when housing is cracked, broken mounting tabs fail, or board access is needed.

• 1 control board housing

• Disconnect power and water to the appliance before beginning any repair.
• Handle the control board and housing carefully to avoid damage to connectors or circuit components.
• Use appropriate tools to remove console components; replace damaged mounting tabs and secure all fasteners.
• Discharge any capacitors and follow the board manufacturer's ESD/safety recommendations.

This upper wash arm directs rotating spray to the dishwasher's top rack to help improve cleaning coverage and reduce food/residue on upper-rack dishes. Fits as the rotating upper spray arm assembly for compatible dishwashers. What it does:

• Rotates and sprays water across the upper rack to help remove stuck-on food and rinse dishes.
• Helps correct weak or uneven spray patterns from the top rack.
• Can reduce spotting and areas that remain soiled when the upper arm is damaged or clogged.
• Replaces a worn, cracked, or clogged upper spray arm to restore proper spray action.

• Always disconnect power to the dishwasher and turn off the water supply before servicing.
• Remove the upper rack to access the arm; unclip or unscrew the old arm and install the replacement until it seats/threads securely.
• Clear any debris from the mounting area and ensure the arm spins freely before running a test cycle.
• Run a short rinse or quick cycle to verify correct spray pattern and fit.

This chopper assembly replaces the food-chopping component in compatible countertop food processors, restoring even chopping and diced results. It helps get blades turning and keeps food processing performing as intended. What it does:

• Spins and chops food inside the processor bowl for consistent results
• Restores proper cutting when chopping is uneven or not happening
• Helps eliminate food buildup that causes noisy or inefficient operation
• Works with the existing drive coupling to transfer motor power to the blades

• Disconnect power and remove the processor bowl and lid before servicing
• Handle blades carefully — they are sharp; wear cut-resistant gloves
• Ensure the part seats fully on the drive coupling and locks into place before use
• Test operation with small amounts of food after reassembly; stop immediately if unusual noise or resistance occurs

This manifold mounting bracket secures the gas manifold assembly to the appliance frame, keeping fuel lines and related components aligned for reliable operation. It's a direct-fit replacement that restores proper manifold support. What it does:

• Holds the gas manifold in the correct position to prevent strain on connections and lines
• Helps maintain stable alignment of valves and supply tubing to reduce leaks and intermittent flow
• Addresses symptoms like a loose or rattling manifold assembly or visible bracket damage
• Restores proper mounting after impact or corrosion-related bracket failure

• One manifold mounting bracket

• Install only with the appliance powered off and gas supply completely shut; follow local codes
• Match bracket orientation to the original and secure with manufacturer-specified fasteners
• Inspect nearby tubing, fittings and valve mounts for damage when replacing the bracket

A filter guard that helps keep debris away from the wash pump and drain area, protecting the pump and improving drain performance. Simple replacement for worn or damaged filter housings. What it does:

• Covers and protects the dishwasher's lower filter area to help prevent large debris from entering the pump
• Helps reduce clogs and poor drain performance caused by food or loose items
• Maintains proper water flow through the filter assembly for more reliable operation
• Works as a replacement for a cracked, warped, or missing filter guard that leaks or allows debris through

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove the lower rack and existing filter assembly to access the guard
• Inspect adjacent filter parts for wear; replace damaged components to ensure proper sealing
• Hand-tighten or seat parts as directed by the OEM; avoid forcing or overtightening plastic components

A stainless pushnut used to secure shafts, studs, or small components with a quick, push-on retainer that resists corrosion. Keeps parts fastened without threading or additional hardware for a clean, low-profile fit. What it does:

• Acts as a push-on retaining nut to hold shafts, studs, or fittings in place
• Provides a corrosion-resistant stainless finish for wet or high-humidity areas
• Prevents components from sliding off axles or posts during normal operation
• Commonly used on control shafts, knobs, or small internal assemblies

• Turn power off and unplug appliance before servicing to avoid shock or injury
• Push onto the post or shaft until fully seated; a firm press or light tap may be required
• Use appropriate hand tools or pliers with protection to avoid damaging the part
• Replace with identical part number to ensure fit and function