Jdb85900awb Parts

This small retaining clip secures trim and appliance components to keep panels and assemblies in place, helping prevent rattling and loose parts during use. It's a simple replacement that restores proper fit and alignment. What it does:

• Holds panels, trim, or small assemblies in place to maintain a secure fit
• Prevents rattling, vibration noise, and movement of loose parts
• Replaces broken, bent, or missing clips that allow gaps or misalignment
• Works where a small fastener is needed to secure plastic or metal components

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Inspect the mounting area for damage; replace any broken mating tabs or screws for a secure fit
• Installation typically requires basic hand tools such as pliers or a screwdriver; apply steady pressure to snap clip into place

This factory fastener is a #10-16 screw used to secure appliance panels and components. Replacing worn or missing hardware restores a tight fit, helps prevent rattles, and keeps parts properly aligned for dependable operation.

• Secures brackets, panels, and covers to the cabinet or frame
• Replaces missing, stripped, or corroded mounting hardware
• Helps reduce vibration and rattling from loose mounts
• Correct 10-16 thread to match designated OEM mounting points

• Disconnect power and shut off water or gas supply before servicing
• Match the screw to the original location using your model's diagram
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

This wire harness routes power and control signals between appliance components to restore reliable electrical connections. Use it when a damaged or shorted harness causes intermittent operation, non-responsive controls, or loss of power to parts. What it does:

• Routes power and signals between the control and components (motors, switches, sensors) to maintain proper electrical paths.
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or blown fuses.
• Addresses common symptoms such as the appliance not starting, controls that don't respond, or specific components failing to run.
• Restores original connector locations and routing for secure, reliable connections.

• Disconnect power (unplug or switch off breaker) before servicing to avoid shock or damage.
• Compare harness routing and connector positions to the removed part before installing to ensure correct fit.
• Reuse original clips and retainers where possible; secure loose wiring away from heat and moving parts.

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Small clip that secures panels, trim or small components to keep parts properly seated and reduce rattling. Replacing a worn or broken clip helps restore fit and stops noise from loose assemblies. What it does:

• Secures trim, panels or small assemblies so parts stay aligned and stable
• Prevents vibration and rattling caused by loose or damaged fasteners
• Helps hold seals or wiring in place where used as a retainer
• Restores proper fit of the affected panel or component after failure

• Disconnect power to the appliance before servicing and work with dry hands
• Remove or loosen adjacent trim or panels as needed to access the clip location
• Note clip orientation, then press or snap the replacement clip into place until fully seated
• Reassemble panels and test appliance operation to confirm the repair

Size: 8-32 x 1/2 inch.

This is the rear wheel support for a dishwasher rack. It helps guide and support the rack as it slides in and out, restoring smooth movement and preventing the rack from binding or derailing.

• Supports and guides the rack at the rear during opening/closing
• Helps correct issues like a wobbly, sticking, or misaligned rack
• Can address noisy, rough rack travel caused by a worn support
• Maintains proper rack tracking to reduce derailment

• Disconnect power and water before servicing
• Pull rack forward to access the rear support area
• Depress locking tabs/retainer to remove the old support; press-fit the new support until secure
• Verify smooth rack travel before returning the appliance to service

This pivot tine fits the fold-down lower shelf and restores the shelf's pivot point so it tilts and holds properly, helping prevent unexpected drops and uneven folding while keeping stored items stable. What it does:

• Serves as the pivot/hinge point for the refrigerator's fold-down lower shelf.
• Holds the shelf in position when folded or extended so items stay supported.
• Replaces broken, worn, or missing pivot hardware that can cause the shelf to sag or fail to latch.
• Helps stop rattling, slipping, or uneven movement at the shelf hinge.

• Remove all items from the shelf and lift the shelf out per your model's instructions before installing.
• Align the pivot tine with the shelf mounting slot or hinge post and press until it snaps or seats securely.
• Inspect the mating bracket/slot for damage before installing; replace any damaged bracketry to ensure proper fit.
• Use gloves to protect hands; disconnect power only if required by your model's service instructions.

This jumper is an OEM-style electrical wire connector used to bridge terminals in a Whirlpool appliance to restore circuit continuity and proper component operation. It's a simple replacement part that helps return power or signal paths when the original jumper is damaged. What it does

• Provides a secure electrical connection between two terminals to complete a circuit.
• Restores power or signal routing to components that lose function due to a broken or corroded jumper.
• Common symptom: component or control doesn't receive power or the appliance won't complete a specific cycle.
• Works with control boards and wiring harness assemblies where a factory jumper is used.

• One jumper electrical connector.

• Disconnect power (unplug appliance or shut off breaker) before service to avoid shock or damage.
• Use insulated tools as needed and make secure, tight terminal connections to prevent arcing.

This upper rack assembly restores the top loading area of your dishwasher and provides stable, organized support for glasses, cups and small dishes in an onyx black finish. Replaces a cracked, bent or missing upper rack. What it does

• Holds and secures cups, glasses and small dishes on the dishwasher's top rack
• Replaces damaged or warped racks that cause items to tip or nest
• Restores proper sliding and alignment if the upper rack catches or rides unevenly
• Matches onyx black interior finishes for a consistent look

• Disconnect power to the appliance before servicing
• May require removal of the lower rack and simple fasteners to slide the upper rack into place
• Handle carefully to avoid scratching the finish or bending rack tines

This upper rack pivot clip secures the rack pivot/tine assembly so the dishwasher's upper rack stays aligned and operates smoothly. Replaces a broken or missing clip to restore proper rack positioning and movement. What it does

• Secures the upper rack pivot/tine so the rack stays level and engages the track
• Prevents the rack from slipping, sagging, or detaching when pulled
• Helps the rack slide smoothly in and out without catching
• Useful when the original clip is cracked, worn, or missing

• Disconnect power to the appliance before starting any repair
• Typically accessed from the side of the dishwasher; basic hand tools may be required
• Handle the small plastic clip carefully — it can snap if over-stressed

This tab-sump mounting secures the dishwasher sump/dispenser area so detergent tabs and related components stay properly aligned. Replacing a worn or broken mounting restores correct dispenser positioning and helps prevent tabs from falling loose during cycles. What it does:

• Holds the tab/sump assembly in place to maintain proper detergent tab positioning
• Prevents the dispenser or sump from shifting or sagging during operation
• Helps reduce incidents of tabs dislodging or failing to stay seated
• Supports correct alignment of adjacent dispenser components

• Disconnect power and water supply before starting any repair
• Remove the door panel or access cover to reach the sump area
• Inspect surrounding clips and seals; replace any damaged fasteners for a secure fit

This dispenser cover is the replacement lid for a washer dispenser assembly, restoring a secure, functional cover that keeps detergent and fabric softener contained until the wash cycle. It helps prevent spills and keeps the dispenser looking finished. What it does:

• Replaces a cracked, warped, or missing dispenser lid so the dispenser closes properly
• Helps contain detergent and softener to prevent drips and spills onto the washer top
• Restores a flush, finished appearance to the dispenser area
• Works with the dispenser housing to ensure proper release of cleaning agents during cycles

• Disconnect power and water supply before servicing the washer
• Replacement typically installs with clips or screws; keep original fasteners and note their placement
• Handle plastic parts carefully to avoid cracking; align tabs before snapping into place