Jdb8700awso Parts

This terminal nut secures a wire terminal to a threaded post or terminal block, ensuring a tight, reliable electrical connection. Replace a missing, stripped, or heat-damaged nut to restore a safe, stable power path to the component. What it does:

• Clamps a ring or spade terminal to a threaded stud/post on a terminal block or component
• Maintains a low-resistance connection to reduce arcing and heat buildup
• Helps address symptoms like loose/burned terminal connections, intermittent power, or discoloration at the connection point
• Direct replacement for the original connection hardware on applicable models

• 1 terminal nut

• Disconnect power at the breaker before servicing; allow any heated components to cool
• Note wire locations; remove damaged hardware and inspect wiring/terminals for heat damage
• Clean threads and install the new nut; tighten snugly without overtightening
• Reassemble and restore power; verify the connection remains cool during initial operation

Cover-Box protects the appliance's control box and internal wiring by enclosing electronic components to keep out dust and accidental contact, helping maintain reliable operation and reduce the chance of component damage. What it does:

• Encloses and protects the control box and wiring from dirt, debris and incidental contact.
• Helps prevent exposed wires and component damage that can lead to intermittent operation or electrical faults.
• Restores structural protection when the original cover is cracked, warped, or missing.
• Matches OEM fit and mounting points to secure the control assembly in place.

• Disconnect power to the appliance before beginning any service.
• Remove screws or fasteners securing the old cover; keep hardware for reuse unless damaged.
• Ensure wiring and connectors are routed correctly and fully seated before reinstalling the cover.

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Small clip that secures panels, trim or small components to keep parts properly seated and reduce rattling. Replacing a worn or broken clip helps restore fit and stops noise from loose assemblies. What it does:

• Secures trim, panels or small assemblies so parts stay aligned and stable
• Prevents vibration and rattling caused by loose or damaged fasteners
• Helps hold seals or wiring in place where used as a retainer
• Restores proper fit of the affected panel or component after failure

• Disconnect power to the appliance before servicing and work with dry hands
• Remove or loosen adjacent trim or panels as needed to access the clip location
• Note clip orientation, then press or snap the replacement clip into place until fully seated
• Reassemble panels and test appliance operation to confirm the repair

Size: 8-32 x 1/2 inch.

This is the rear wheel support for a dishwasher rack. It helps guide and support the rack as it slides in and out, restoring smooth movement and preventing the rack from binding or derailing.

• Supports and guides the rack at the rear during opening/closing
• Helps correct issues like a wobbly, sticking, or misaligned rack
• Can address noisy, rough rack travel caused by a worn support
• Maintains proper rack tracking to reduce derailment

• Disconnect power and water before servicing
• Pull rack forward to access the rear support area
• Depress locking tabs/retainer to remove the old support; press-fit the new support until secure
• Verify smooth rack travel before returning the appliance to service

A replacement duct vent that restores the dryer's exhaust outlet, directing moist air safely outside. Replaces a damaged or missing vent to help maintain proper exhaust airflow and reduce lint buildup where the duct terminates. What it does:

• Provides the finished exhaust outlet for the dryer's vent system.
• Directs dryer air and lint out of the appliance, preventing airflow restriction at the termination point.
• Replaces cracked, broken, or missing vents that can cause air leakage or visible lint accumulation.
• Helps resolve symptoms such as poor dryer venting, lint collecting around the exhaust opening, or airflow escaping through gaps.

• Disconnect power to the appliance before beginning work; if installing on a gas dryer, turn off the gas supply and follow all safety precautions.
• Use appropriate hand tools, a screwdriver, and corrosion-resistant fasteners; wear gloves to avoid sharp edges.
• Follow manufacturer instructions and local venting codes; inspect and clean the vent path while the vent is replaced.

A front status/indicator light that restores visible feedback from the appliance control panel. Replaces a burned-out or non-functioning front indicator so you can see operating or status changes at a glance. What it does:

• Provides a visible indicator on the front control panel — use when the light no longer illuminates.
• Signals operational changes and status conditions — fixes dim, flickering, or intermittently working indicator lights.
• Restores clear front-panel feedback for normal user checks — helpful when the display no longer shows expected status.

• Disconnect power before starting any repair to avoid shock or damage.
• Access may require removing the control console or front bezel; keep screws and small parts organized.
• Handle the light and lens carefully to avoid damage; use appropriate tools.

This pivot tine fits the fold-down lower shelf and restores the shelf's pivot point so it tilts and holds properly, helping prevent unexpected drops and uneven folding while keeping stored items stable. What it does:

• Serves as the pivot/hinge point for the refrigerator's fold-down lower shelf.
• Holds the shelf in position when folded or extended so items stay supported.
• Replaces broken, worn, or missing pivot hardware that can cause the shelf to sag or fail to latch.
• Helps stop rattling, slipping, or uneven movement at the shelf hinge.

• Remove all items from the shelf and lift the shelf out per your model's instructions before installing.
• Align the pivot tine with the shelf mounting slot or hinge post and press until it snaps or seats securely.
• Inspect the mating bracket/slot for damage before installing; replace any damaged bracketry to ensure proper fit.
• Use gloves to protect hands; disconnect power only if required by your model's service instructions.

This jumper is an OEM-style electrical wire connector used to bridge terminals in a Whirlpool appliance to restore circuit continuity and proper component operation. It's a simple replacement part that helps return power or signal paths when the original jumper is damaged. What it does

• Provides a secure electrical connection between two terminals to complete a circuit.
• Restores power or signal routing to components that lose function due to a broken or corroded jumper.
• Common symptom: component or control doesn't receive power or the appliance won't complete a specific cycle.
• Works with control boards and wiring harness assemblies where a factory jumper is used.

• One jumper electrical connector.

• Disconnect power (unplug appliance or shut off breaker) before service to avoid shock or damage.
• Use insulated tools as needed and make secure, tight terminal connections to prevent arcing.

This upper rack pivot clip secures the rack pivot/tine assembly so the dishwasher's upper rack stays aligned and operates smoothly. Replaces a broken or missing clip to restore proper rack positioning and movement. What it does

• Secures the upper rack pivot/tine so the rack stays level and engages the track
• Prevents the rack from slipping, sagging, or detaching when pulled
• Helps the rack slide smoothly in and out without catching
• Useful when the original clip is cracked, worn, or missing

• Disconnect power to the appliance before starting any repair
• Typically accessed from the side of the dishwasher; basic hand tools may be required
• Handle the small plastic clip carefully — it can snap if over-stressed

This tab-sump mounting secures the dishwasher sump/dispenser area so detergent tabs and related components stay properly aligned. Replacing a worn or broken mounting restores correct dispenser positioning and helps prevent tabs from falling loose during cycles. What it does:

• Holds the tab/sump assembly in place to maintain proper detergent tab positioning
• Prevents the dispenser or sump from shifting or sagging during operation
• Helps reduce incidents of tabs dislodging or failing to stay seated
• Supports correct alignment of adjacent dispenser components

• Disconnect power and water supply before starting any repair
• Remove the door panel or access cover to reach the sump area
• Inspect surrounding clips and seals; replace any damaged fasteners for a secure fit