Jenn-Air Dw730b Parts

This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.

Dishwasher lower wash arm and spray tower support.

This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.

Long tub insulation that fits the appliance's inner tub, reducing operating noise and helping stabilize temperature around the tub for quieter, more consistent performance. Replaces worn or damaged insulation to address rattles and drafts. What it does:

• Dampens noise and vibration when insulation is torn, compressed or missing.
• Helps limit heat loss and reduce cold spots that can cause condensation or longer warm-up times.
• Reduces rattling or knocking caused by loose or degraded insulation.
• Intended for specific Whirlpool tubs—verify model fit before ordering.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove outer panels or drum components per the service manual; insulation may be held with clips, adhesive, or fasteners.
• Wear gloves and a dust mask—insulation fibers can irritate skin and lungs.

To order indicator lens use WP22001948.

This rack stop clips onto the end of a dishwasher rack rail to keep the rack from sliding off the track. Replacing a worn or missing stop helps the rack glide securely and prevents accidental pull-outs during use.

• Prevents the rack from being pulled out too far and falling off the rail
• Helps restore smooth, secure rack operation
• Common fix for racks that slide out too far or feel unstable

• Disconnect power and turn off water before servicing
• Pull the rack forward, depress the old stop's locking tab, and remove
• Align and snap the new stop onto the rail end until it locks
• Check rack travel to ensure the stop is fully engaged

This small rubber grommet seals the opening around the dishwasher's detergent/rinse-aid dispenser, helping prevent leaks and moisture intrusion so the dispenser operates reliably throughout the wash cycle.

• Seals the dispenser passage to keep water from leaking into or out of the dispenser cavity
• Helps ensure proper detergent or rinse-aid dispensing
• Can reduce moisture-related corrosion or staining in the dispenser area

• Disconnect power and turn off water before servicing
• Remove inner door panel to access the dispenser assembly
• Note grommet orientation; seat fully to ensure a watertight seal
• Inspect surrounding surfaces for debris or damage before reassembly

The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.

• Provides rolling support so the tub can move and self-balance during cycles
• Reduces friction between the tub and the base/frame
• Helps keep the tub centered to minimize noise and vibration
• Failure symptoms include squeaking or grinding, scraping noises, dragging movement, or visible flat spots/cracks on the wheel

• Disconnect power and water supply before servicing; wear appropriate gloves and eye protection
• Access the base/suspension per the service information and support the tub to remove load from the wheel
• Remove the retainer/axle, install the new wheel, and free rotation and correct orientation
• Reassemble, level the appliance, and run a spin test to check for noise and balance

Screw: 8-16 x 3/8 inch.

This replacement screw secures appliance panels, brackets, and components. Using the correct size restores a snug fit to reduce vibration, prevent loosening, and keep assemblies properly aligned during operation. What it does:

• Fastens sheet metal and component brackets in designated locations
• Replaces missing, stripped, or corroded hardware
• Helps eliminate rattling and vibration from loose panels
• Maintains proper alignment of covers and assemblies

• 1 screw

• Disconnect electrical power; shut off water or gas supplies if applicable
• Match length/thread to the original; replace one fastener at a time to preserve alignment
• Start by hand to avoid cross-threading; use the correct driver size
• Snug firmly but do not overtighten to prevent stripping

Specs: No.8X1/2 HEX WASHER HEAD

A small trim screw designed to secure appliance trim pieces and molding, restoring a finished look and keeping panels held firmly in place. Ideal when a trim piece is loose, missing a fastener, or shows minor rattling. What it does:

• Fastens trim, molding, or decorative panels to the appliance frame
• Restores secure mounting and helps eliminate loose or rattling trim
• Replaces missing or stripped fasteners that cause gaps or poor fit
• Compatible with common trim attachment points where OEM screw is specified

• Disconnect power or unplug the appliance before attempting repairs
• Use the correct screwdriver bit to match the screw head to avoid stripping
• Install by hand to start threads, then tighten snugly—do not overtighten
• Verify trim alignment after installation and test that the panel is secure

This tub wheel mounts on the dishwasher's tub wall to guide and support the rack as it slides in and out. Replacing a worn wheel restores smooth rack movement and helps prevent binding, noise, and derailments.

• Mounts to the tub to provide rolling support for the dish rack/rail
• Replaces cracked, flattened, or missing wheels that impede rack travel
• Helps fix racks that stick, bind, are hard to pull/push, or derail
• Reduces grinding or squeaking from the rack area

• Disconnect power at the breaker before servicing
• Open the door and pull the rack forward for access
• Release the old wheel from its retainer/axle per your model's design; install the new wheel in the same orientation
• Ensure the wheel spins freely and the rack slides smoothly before use

Small replacement screw that secures panels and internal components on compatible appliances. Restores proper fastening to reduce rattling and loose parts so controls and panels stay aligned during normal use. What it does:

• Secures panels, brackets, and small components to the appliance frame or assemblies.
• Helps stop rattling, vibration-related noise, and movement from loose parts.
• Replaces a missing, worn, or stripped fastener to restore proper mounting.
• Used wherever the original manufacturer specified this screw in service diagrams.

• Disconnect power and water before working on the appliance to avoid shock or injury.
• Match the replacement screw to the original by fit and thread before installation; do not force mismatched fasteners.
• Start the screw by hand to avoid cross-threading; tighten securely but avoid over-torquing which can strip threads or damage components.
• Refer to the appliance's service manual or parts diagram for exact location and any torque or threadlocker recommendations.

This upper spray arm sprays water across the top rack to help remove food and rinse dishes for better cleaning coverage. It replaces a damaged or clogged upper spray arm to restore normal spray pattern. What it does

• Directs pressurized water to clean dishes on the upper rack
• Helps reduce missed spots and improve rinse performance
• Replaces worn, cracked, or clogged upper spray arms
• Works with the dishwasher's existing spray system and fittings

• Disconnect power to the dishwasher (unplug or turn off circuit breaker) before servicing
• Turn off the water supply to the appliance if required by your model
• Remove the upper rack to access the spray arm; handle gently and avoid forcing fittings
• Run a short test cycle after installation to ensure proper fit and spray coverage

A replacement tension spring designed to restore proper movement and return force to the appliance mechanism. Helps the affected component operate smoothly so doors, levers or assemblies move with correct tension and alignment. What it does:

• Provides return and holding tension for the appliance mechanism to restore normal movement.
• Helps reduce sagging, misalignment, or loose operation of the associated door or linkage.
• Minimizes noise and vibration caused by a worn or weakened spring.
• Works as the direct-fit part when the listed part number matches your appliance.

• Disconnect power and water (if applicable) before beginning any repair.
• Springs are often under tension—wear eye protection and use caution when removing or installing.
• Follow the appliance's service manual or OEM instructions for correct orientation and safe installation.