Jgbs66rek Parts

Upper back cover panel for gas ranges. Protects internal components and completes the exterior finish. Replace if cracked, damaged, or missing.

Insulation pad fits behind your range oven door to reduce heat loss and lower exterior temperature. Replace if worn, damaged, or oven struggles to hold heat.

Decorative side foil trim that covers the outer edge of your range panel. Replace when cracked, peeling, or missing to restore a finished look.

Support plate for gas range burners. Mounts beneath burner assembly to provide stable base. Replace if cracked, warped, or missing to restore proper fit.

Insulation guard protects wiring and components from heat damage in your range. Replace if cracked, deteriorated, or missing to maintain safe operation.

Fix loose or rattling control panels with this range panel backer. Secures and aligns the control panel while protecting internal wiring and switches.

Side panel for gas ranges. Replaces cracked, dented, or damaged exterior panels. Installs on the side of the range to restore appearance and protect internal components.

Fix uneven flames or burners that won't light properly with this gas range burner diverter. Direct replacement part restores proper gas flow distribution.

This diverter side is a replacement housing piece that helps route flow inside the refrigerator dispenser or diverter assembly, restoring proper function to the dispensing pathway. It provides a direct swap for the worn or damaged original. What it does:

• Forms one side of the internal diverter assembly that directs water/ice/air flow inside the dispenser area
• Can stop flow issues caused by a cracked or broken housing
• Helps prevent leaks or misdirected dispensing when the original part is damaged
• Useful when the dispenser produces sputtering, weak flow, or visible housing damage

• Disconnect power and turn off the water supply before starting any repair
• Minimal hand tools required; follow OEM diagram for proper orientation and clips/tabs
• Inspect adjacent seals and gaskets and replace if cracked to ensure a watertight fit
• Test dispenser for proper flow and leaks after installation

Replace the top complement backguard on your gas range. This cosmetic panel covers the rear cooking surface. Order a new one if cracked or damaged.

This bottom panel replaces the damaged lower oven floor panel to restore proper support and heat protection for cookware and internal components. It helps stop rattling, sagging, and hot spots that can affect bake performance. What it does:

• Provides a stable, heat-resistant surface at the bottom of the oven cavity
• Protects underlying components from spills, drips and direct heat
• Prevents sagging or warped oven floor that can cause cookware instability
• Can reduce rattling or vibration caused by a loose or damaged panel

• Disconnect power to the range before beginning any work.
• Remove oven racks and allow the oven to cool completely.
• Handle edges carefully; use gloves to avoid cuts and protect the finish.
• Installation typically requires removing access screws and aligning the panel into the oven floor supports.

Replace a cracked or damaged broiler panel in your range oven cavity. This inner panel restores the broiler surface and protects internal components.

This rubber grommet cushions and seals a panel opening to protect wires, hoses or tubing from chafing and vibration. It helps prevent wear and keeps wiring routed cleanly through metal or plastic panels. What it does:

• Provides a protective, vibration-dampening barrier where wiring or tubing passes through a hole
• Helps stop chafing that can cause exposed insulation or hose damage
• Reduces noise from vibration where parts contact a cabinet or chassis
• Keeps the opening sealed against debris and light moisture intrusion

• One rubber grommet as shown

• Disconnect power and water before accessing panels
• Inspect the opening and mating surfaces; remove rust or sharp edges before installing
• Press grommet into the hole until fully seated; ensure wiring or tubing is routed without pinching
• Replace grommet if torn, hardened, or deformed; use only the specified size for a secure fit

This rangetop holder is a small support bracket that secures the cooktop/rangetop assembly and helps keep burners and trim properly aligned for safe, even cooking. It replaces a worn or damaged holder to restore stable cooktop support. What it does:

• Supports and stabilizes the rangetop/cooktop assembly to prevent shifting or sagging
• Keeps burner components and trim aligned for proper burner placement and operation
• Helps eliminate rattling or movement under normal use
• Addresses symptoms such as a loose or misaligned cooktop, noisy operation, or uneven burner spacing

• One rangetop holder support bracket

• Disconnect power and gas supply before beginning any repair
• Remove cooktop trim or grates as needed to access the holder; hand tools such as screwdrivers may be required
• Handle edges carefully to avoid cuts and protect finished surfaces from scratches
• Test fit and reassemble components to ensure proper alignment before restoring power/gas