Jjw3560cab Parts

Replace your worn or damaged 30-inch rolling oven rack. Installs inside wall oven cavity to hold cookware. Needed when rack is bent or missing.

Replaces cracked, broken, or missing bottom vent trim on your wall oven. Covers the lower front vent opening for a finished look and proper airflow.

This factory fastener secures components inside your appliance, keeping panels, brackets, and assemblies properly attached. Replacing a worn, stripped, or missing screw restores a tight fit and helps prevent vibration, rattling, and misalignment.

• Fastens parts to frames, panels, or brackets as specified in your model's parts diagram
• Helps maintain alignment and reduce vibration/rattling during operation
• Replace when the original screw is missing, corroded, stripped, or no longer holds
• Direct OEM hardware for the designated locations on applicable models

• Disconnect power; shut off gas/water if applicable. Allow hot surfaces to cool.
• Use the correct driver size; start threads by hand to avoid cross-threading.
• Tighten until snug—do not overtighten, especially into plastic or thin sheet metal.
• If a mating clip, insert, or nut is damaged, replace that hardware per your model diagram.

This is a black decorative trim piece that covers the lower ventilation opening on the front of a wall oven. It directs hot exhaust air out of the oven cavity while providing a finished appearance. Replace this trim if it is cracked, warped from heat exposure, discolored, or missing.

Fix uneven baking or no convection heating in your wall oven with this convection fan motor. Moderately easy repair that restores proper air circulation.

This is a hex nut used in wall oven assembly to secure various internal components and mounting hardware. It provides a threaded fastening point that holds parts firmly in place during operation. Replace this nut if it is stripped, corroded, or missing, which can cause loose components or rattling during use.

Non-corrosive silicone adhesive sealant for appliance repairs. Replace cracked or missing seals on door panels, trim strips, and interior edges.

6-32 machine screw secures panels, brackets, and components in appliances. Replace worn, missing, or stripped screws to restore proper fit and assembly.

Fix an oven that won't read the meat probe temperature. This probe jack restores the electrical connection for accurate temperature monitoring.

This mounting bracket is a replacement support bracket that secures appliance components and keeps assemblies aligned for reliable operation. It restores proper fit and helps prevent rattling or movement from loose fittings. What it does:

• Secures panels or assemblies to the appliance frame to maintain proper alignment
• Reduces vibration and rattling caused by loose or damaged supports
• Restores mounting points that prevent sagging or separation of connected parts
• Helps ensure stable operation after repairs involving removed or replaced hardware

• Follow the appliance service manual for exact location and fastener torque
• Disconnect power (and gas if applicable) before beginning any repair
• Use appropriate tools and replace any damaged screws or clips with OEM-equivalent fasteners

This genuine replacement wire harness routes power and signals between control components to restore reliable electrical connections. It replaces damaged or worn wiring to help fix intermittent power, non-responsive controls, or component failures. What it does

• Connects control board, switches and sensors to supply power and signal paths
• Restores broken or frayed wiring that can cause intermittent operation or no power
• Provides correct factory-configured terminals and connector shapes for a secure fit
• Helps resolve symptoms like unresponsive controls, lighting or motor not operating reliably

• One wire harness (single assembly)

• Disconnect power before beginning service to avoid shock or short circuits
• Inspect connectors and routing; replace any retaining clips or grommets that are damaged
• Route harness the same way as the original to prevent chafing or pinching

Maintains oven door structure and secures the glass panels in place. Replace if cracked, broken, or missing to restore proper door assembly and fit.

Secures oven door glass to the door assembly, maintaining stability and proper seal. Replace if worn or broken to restore door alignment. Verify fit with your model.

Inner or outer glass panel for wall oven doors. Replaces cracked, shattered, or broken glass that compromises visibility and door seal integrity.

Genuine mounting screw secures panels, brackets, and internal components in wall ovens and ranges. Replace stripped, missing, or worn fasteners.