Jmcdavittlaurelhillcom Parts

Non-corrosive silicone adhesive sealant for appliance repairs. Replace cracked or missing seals on door panels, trim strips, and interior edges.

Microwave light reflector directs bulb illumination inside cooking cavity. Replace if cracked, discolored, or missing to restore proper lighting. Confirm fit with your model number.

This genuine replacement wire harness routes power and signals between control components to restore reliable electrical connections. It replaces damaged or worn wiring to help fix intermittent power, non-responsive controls, or component failures. What it does

• Connects control board, switches and sensors to supply power and signal paths
• Restores broken or frayed wiring that can cause intermittent operation or no power
• Provides correct factory-configured terminals and connector shapes for a secure fit
• Helps resolve symptoms like unresponsive controls, lighting or motor not operating reliably

• One wire harness (single assembly)

• Disconnect power before beginning service to avoid shock or short circuits
• Inspect connectors and routing; replace any retaining clips or grommets that are damaged
• Route harness the same way as the original to prevent chafing or pinching

This interlock is the door switch that tells the washer or dryer the door is closed so the appliance can run. It restores normal start and cycle operation by completing the door-close signal to the control. What it does:

• Detects when the door or lid is closed and signals the control to allow operation
• Prevents the appliance from starting or spinning when the door is open
• Commonly replaces a failed switch that causes no-start, no-spin, or interrupted cycles
• Works as the safety/closure sensor used by the machine's control board

• Disconnect power (and water for washers) before servicing to avoid shock or injury
• Access and replacement steps vary by model; remove cabinet or console panels as required
• Handle connectors and wiring gently; ensure proper connector seating and door alignment before testing

Fixes uneven cooking or browning in convection mode. This motor circulates heated air throughout the cavity for consistent baking results.

Replace cracked or fogged inner oven door glass pane. Restores heat barrier between oven cavity and kitchen. Fits between door panels for proper insulation.

Color: Citrine white. Size: 0.6 fl.oz. Bottle with brush.

Secures and powers the G4-base bulb for reliable interior lighting. Replace if bulb flickers, won't stay seated, or socket is damaged. Confirm fit.

Fix F2E1 error codes or unresponsive buttons with this microwave control panel. Houses display, timing controls, and power settings for operation.

This power supply is the electronic control board that provides the regulated voltages and control signals needed for the appliance's user console and main controls to operate reliably. It restores proper power distribution so controls can respond. What it does:

• Converts incoming AC to the low-voltage DC used by the console and control circuitry.
• Powers display, buttons, and control relays so the appliance can receive and execute commands.
• Common symptom: blank or unresponsive display/console.
• Common symptom: intermittent or total loss of control functions, or failure to start cycles.

• Disconnect power before servicing to avoid electrical shock.
• Handle the board by its edges and avoid ESD (static) damage—use proper grounding.
• Reassemble panels and secure connectors fully; test control functions after installation.

This is the inner door panel assembly for a microwave oven. It sits on the interior side of the door and typically houses the choke cover, interlock switches, and inner window that help contain microwave energy during operation. Replace this assembly if the inner panel is cracked, warped, or if the door no longer latches or seals properly.

Seals the appliance door to prevent leaks and keep the interior working as intended. Replace a cracked, torn, or hardened gasket to stop leaks, reduce odor and mold, and restore a reliable door seal. What it does:

• Forms a tight seal between the door and cabinet to prevent water, air, or heat loss
• Stops common symptoms like visible cracks or gaps, water pooling, and persistent odors
• Restores proper containment for cleaning, heating, or washing cycles
• Matches the OEM channel/retainer design for a secure fit

• Disconnect power and water before beginning any repair
• Remove the old gasket, thoroughly clean the mounting area, then seat the new gasket into the door channel or retainer
• Work the gasket evenly around the door; avoid overstretching and ensure all beads/clips are fully engaged