Js760sl566 Parts

This oven door gasket forms the heat-resistant seal around the oven door opening. Replacing a worn seal helps the oven preheat and hold temperature, reduces heat and steam escaping at the door, and supports consistent cooking results.

• Seals the gap between the oven cavity frame and the door to contain hot air and steam
• Helps maintain stable temperatures and more even baking/roasting
• Replace if you notice fraying, tears, flattened sections, or visible gaps around the door
• Symptoms of a failing seal can include longer preheat or cook times and heat escaping around the door

• Disconnect power and let the oven cool completely before servicing
• Remove the old gasket and clean the mounting area of any debris
• Install the new gasket following the original routing; seat retainer points evenly and do not stretch the gasket
• Close the door to confirm uniform contact, then run a short heat cycle to verify no leaks

A stainless infinite knob that replaces a worn or broken range or oven control knob, restoring smooth selection of heat/power settings and a clean stainless look for your appliance controls. What it does:

• Fits onto the stove/range infinite control shaft to set burner or oven power levels.
• Replaces cracked, chipped, or missing knobs that won't turn or slip on the control shaft.
• Restores precise user control when settings are hard to select or the knob is loose.
• Matches stainless control panels for a consistent, refreshed appearance.

• Disconnect power to the appliance before servicing to reduce shock risk.
• Typically installs by hand: pull the old knob straight off, align splines, and press the new knob onto the shaft until seated.
• Do not force the knob; if it won't seat easily, verify spline alignment and shaft condition.

The Stainless Control Panel Overlay is an OEM part for GE ranges. It provides a protective barrier over the control panel display and buttons. This overlay shields sensitive electronic components from damage.

Symptoms of a bad control panel overlay include:

• Peeling or bubbling of the overlay surface  
• Cracks or missing pieces that expose underlying parts
• Dulling or discoloration of the installed overlay
• Unreadable display or unresponsive control buttons

Causes of control panel overlay failure include repeated exposure to heat from the cooktop or oven, as well as substances dropped while cooking. Heavy use over several years also contributes to degradation of the overlay materials. 

This part is also compatible with some Hotpoint and RCA models.

This oven rack provides a stable, level surface for bakeware and cookware inside the oven cavity. Replace a missing, bent, or corroded rack to restore safe loading and consistent placement on the correct cooking level.

• Supports pans and dishes; slides on the side rails to position food at different heights
• Replace if the rack is missing, bent/warped, rusted, or has a flaking/chipped finish
• Common symptoms include the rack not sitting level, falling off the rails, or not sliding smoothly
• Restores proper, secure placement of cookware for baking, roasting, and broiling

• Disconnect power and allow the oven to cool completely before servicing
• Pull the existing rack forward and lift to remove; align the new rack with both side rails
• Push the rack straight back until fully seated and the stops engage
• Verify the rack is stable before loading cookware; remove racks before a self-clean cycle if your manual directs

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The drawer wedge aligns and stabilizes your range's lower storage/warming drawer so it slides smoothly and closes flush. Replacing a worn wedge restores proper fit and helps prevent rattling, scraping, and an uneven drawer gap.

• Keeps the lower drawer centered and level in the cabinet
• Provides a firm stop/spacing for a flush, consistent close
• Reduces side-to-side play and vibration during use
• Common symptoms: crooked drawer, uneven front gap, scraping noises, drawer not closing fully

• Disconnect power and allow the range to cool before servicing
• Remove the lower drawer to access the wedge location
• Note the wedge's orientation; install the new wedge in the same position
• Reinstall the drawer and verify smooth travel and proper alignment

The Convection Motor is an OEM part for GE electric ranges. It is the component responsible for circulating hot air around food inside the oven cavity during convection cooking cycles. 

Causes of a bad convection motor include failed windings, worn bearings, or damage from excess heat over time.

Symptoms of a bad convection motor include:

• Inability to select convection cooking functions 
• Lack of air movement inside the oven
• Slower than normal cooking times 
• Uneven baking or roasting results

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This halogen lamp assembly provides the oven's interior light, letting you see food clearly without opening the door. It replaces a failed or dim oven light and restores full interior illumination for safer, easier cooking. What it does

• Replaces a burned-out or flickering oven interior light bulb
• Restores bright, clear lighting to check food without opening the oven door
• Fits oven lamp housing and connects to the factory lamp socket
• Common symptom: oven light is dark, flickering, or intermittent

• One halogen lamp assembly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Allow the oven to cool completely before accessing the lamp area
• Avoid touching the glass bulb with bare hands; use a clean cloth or gloves to prevent oils from shortening bulb life

This silicon controlled rectifier (SCR) switches and regulates power to heating elements and motors in compatible appliances, restoring controlled current flow for proper operation. It's a direct-replacement electronic switching component. What it does:

• Acts as a solid-state switch to control AC power to heater or motor circuits
• Helps regulate current during timed or thermostatic cycles
• Common replacement when appliance shows intermittent heating, no heat, or erratic motor control
• Replaces a failed/shorted SCR that can cause blown fuses or control board errors

• One silicon controlled rectifier (single SCR)

• Intended for technicians or experienced DIYers; disconnect power before servicing
• Verify correct SCR orientation and secure the 8-32 screw terminal; avoid overtightening
• Observe ESD precautions and handle the part by non-conductive areas

A safety thermostat that stops the heater when internal temperatures get too high to protect the appliance and prevent overheating. Replaces a worn or failed high-limit switch to restore normal heater safety control. What it does:

• Monitors internal heat and opens the circuit if temperatures exceed safe limits
• Prevents continuous heating and reduces risk of overheating or fire
• Common symptom: dryer or oven heats erratically, overheats, or stops heating unexpectedly
• Works as a non-resettable safety cut-out in the appliance's vent or burner circuit

• Disconnect power (unplug appliance or switch off breaker) before servicing
• Handle terminals carefully; replace any damaged connectors and secure spade terminals fully

The Rear Vent Trim and Gasket Assembly is an OEM part for GE ranges. It seals the rear vent opening of the range, directing hot air and potential gas fumes outside through the exhaust vent during oven use. Without an intact seal provided by the gasket and vent trim, combustion byproducts can enter the kitchen presenting safety and performance issues.

Causes of a bad range rear vent assembly include wear over years of use with high heat cycles, cracking or degradation of sealing materials, or damage from cleaning or impacts around the vent area.

Symptoms of an issue include:

• Foul odors detected in the kitchen during use of the oven
• Inefficient or uneven baking and broiling
• Visible openings or gaps seen around the rear vent perimeter
• Detached, cracked, or missing components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement screw that secures panels, trim and internal brackets to keep appliance components stable and rattle-free. Use when originals are missing, stripped, or broken to restore proper fit and safe operation. What it does:

• Secures panels, control housings, trim and small brackets so parts stay aligned and stable.
• Replaces missing or damaged fasteners that cause rattling, vibration, or loose assemblies.
• Keeps electrical and mechanical components properly positioned for reliable operation.
• Intended as a direct replacement where the OEM screw specified for the application is required.

• Disconnect power and unplug the appliance before starting any repair.
• Use the correct screwdriver or bit and seat the screw squarely to avoid stripping the head or threads.
• Do not overtighten—stop when snug to prevent damage to panels or plastic components.
• Keep removed screws organized; replace only with the identical OEM screw for proper fit.

The Badge Assembly is an OEM part for GE ranges. It includes the magnetic decorative badge affixed to the front of the range. This badge displays important information such as the brand name, model number, and technical specifications.

Causes of a bad badge assembly can include damage from impacts or abrasions over time, adhesive failure from repeated heat exposure, or normal wear from routine cleaning. On a range, the badge must withstand higher cooking temperatures.

Symptoms of a bad badge assembly include:

• Faded or illegible print on the badge face
• Cracks or breaks in the plastic material
• The badge lifting or peeling away from the surface
• Missing or loose attachment clips/fasteners

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This Hub Blade Assembly replaces a worn or damaged blade hub to restore proper blade mounting and rotation. It secures the blade to the motor/hub so the appliance can circulate air or move contents as intended. What it does:

• Replaces the hub that holds and centers the blade, maintaining secure blade attachment
• Restores smooth rotation and reduces wobble or vibration from a loose or broken hub
• Helps stop rattling, uneven operation, or reduced airflow caused by a damaged hub
• Works as the direct mounting point between the motor/hub shaft and the blade

• One hub blade assembly

• Disconnect power before attempting any repair to avoid shock or injury
• Handle sharp blade edges carefully; use gloves and proper tools when removing/installing
• Inspect the motor shaft and fasteners for wear; replace any damaged hardware

This is a replacement M4 hex nut used to secure small appliance panels, brackets, and assemblies. It provides a simple, reliable fastening point to restore proper fit and reduce rattles or loose parts. What it does:

• Secures panels, brackets, fasteners and small components in appliances
• Replaces missing or damaged nuts that allow parts to shift or rattle
• Restores proper thread engagement for M4-0.7 machine screws
• Helps maintain alignment of mounted assemblies when tightened correctly

• Turn off and unplug the appliance and remove power source before starting work
• Hand-start the nut to avoid cross-threading, then tighten snugly with the correct wrench; do not overtighten
• Replace any fasteners with damaged threads or stripped heads for a secure repair

A replacement door side frame that restores the oven door's fit and appearance. This black side trim replaces damaged or worn door framing to help the door close and seal correctly while improving cosmetic condition. What it does:

• Replaces a cracked, chipped, or warped door side frame to restore door alignment and finish
• Supports the door assembly and maintains the correct spacing for the door seal
• Addresses visible cosmetic damage and helps prevent drafts around the oven door
• Matches original mounting points for a direct fit when the correct OEM part is used

• One (1) door side frame (black)

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Remove the oven door or open it to the service position per the manufacturer's instructions for safe access
• Handle glass and painted surfaces carefully to avoid scratches; use proper fasteners and torque per OEM guidance