Jsd9860bdb Parts

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).

This replacement door gasket restores a tight seal to your refrigerator/freezer, helping maintain proper cooling and reduce moisture buildup. It's the direct-fit seal designed to replace a worn, torn, or misshapen gasket for reliable temperature control. What it does:

• Seals the door frame to keep cold air inside and warm, humid air out
• Reduces frost and condensation that can form from a failing seal
• Helps prevent uneven temperatures and food spoilage caused by gaps or leaks
• Use when the existing gasket shows visible gaps, cracks, tears, or persistent condensation

• Disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the mounting channel with a mild cleaner and a soft cloth
• Press the new gasket into the channel, starting at the corners and working around the door until fully seated; ensure the magnetic strip aligns with the door frame
• Check door alignment and close/latch operation after installation; adjust hinges if needed

This temperature control thermostat regulates the refrigerator compartment temperature by cycling the cooling system on and off. Replacing a faulty control restores consistent cooling and normal on/off operation so food stays at the right temperature.

• Senses compartment temperature and opens/closes electrical contacts to start or stop cooling
• Useful when the fridge is too warm or too cold despite adjustments
• Common symptoms: runs constantly or won't run, temperatures don't respond to the dial, no click or change when turning the control
• Also called a "cold control"; restores functional temperature adjustment

• Disconnect power before servicing
• Note wire locations and transfer them to the new control
• Carefully route the sensing capillary in the original path; avoid kinking or sharp bends
• Set to a mid-range setting and allow up to 24 hours for temperatures to stabilize

This heater and thermostat assembly replaces the dryer's heating module to restore normal drying performance by regulating and producing heat. It's a direct-fit assembly designed to simplify replacement and reduce diagnosis time. What it does:

• Provides the dryer's primary heating element and temperature control components.
• Regulates operating temperature via built-in thermostats/thermal cutouts.
• Stops heating when a thermostat or thermal cutoff opens, which can cause no-heat or under-heating symptoms.
• Helps address common symptoms like no heat, long dry times, or intermittent heating when diagnosed to this assembly.

• Disconnect power to the appliance before starting service to avoid shock or injury.
• Carefully discharge any residual heat and avoid contact with sharp sheet metal and the heating element.
• Inspect and replace any blown thermal fuses or damaged wiring.
• Follow model-specific instructions and torque/electrical guidelines from the OEM during installation.

This defrost heater clip secures the refrigerator's defrost heater to the evaporator assembly, keeping the heater in proper position for reliable defrost cycles and helping prevent ice buildup that impairs cooling performance. What it does:

• Secures the defrost heater to the evaporator so the heater maintains proper contact and alignment.
• Helps ensure the heater can melt frost and ice during automatic defrost cycles.
• Small replacement part that restores proper heater placement without replacing the entire assembly.

• Disconnect power to the appliance before accessing the evaporator or heater to avoid shock or injury.
• Replacement typically requires removing interior panels or an evaporator cover; handle evaporator fins carefully—they are sharp.
• Verify the heater and wiring are undamaged and positioned correctly when installing the clip.

Color: white. Measures about 2/3 of an inch wide by 1/2 an inch deep.

This small rubber grommet cushions and supports a fan motor, helping reduce vibration and noise while the appliance is running. It fits into the motor bracket to provide a snug, insulated mounting point.

• Isolates fan motor vibration to cut rattling or buzzing
• Helps keep the motor aligned in its bracket
• Can wear, crack, or compress over time, causing vibration or noise
• Replacing a deteriorated grommet restores smooth, quieter operation

• Disconnect power before servicing
• Access the fan assembly and support the motor to relieve strain
• Note grommet orientation; transfer any sleeves or hardware as found
• Seat the new grommet fully in the bracket before remounting the motor

This hose clamp secures a rubber or plastic hose to its fitting on your appliance, maintaining a tight, leak-resistant seal under vibration and pressure. Replace when the old clamp is rusted, bent, or no longer holds tension. What it does:

• Clamps around a hose to grip the fitting and seal the joint
• Helps prevent drips, leaks, and hose blow-off at the connection
• Restores secure clamping force when the original is worn or damaged
• Common symptoms: water at the connection, hose slipping off, visible corrosion or distortion

• 1 hose clamp

• Disconnect power and shut off the water supply before servicing
• Slide clamp onto hose, seat hose fully on the fitting, then position clamp just behind the bead/raised lip
• Tighten or compress evenly with the appropriate tool; avoid overtightening that could damage the hose
• After reassembly, run a short test and inspect for leaks

This white dispenser fountain bracket secures the small collection/fountain area beneath the refrigerator dispenser, restoring proper alignment and support for the dispenser assembly. It's a direct-replacement part used where the fountain bracket is broken or loose. What it does:

• Supports and secures the dispenser fountain/collection tray to the cabinet or dispenser housing.
• Keeps the fountain aligned so the dispenser fits flush and stays stable during use.
• Commonly replaced when the fountain or surrounding area is loose, cracked, rattles, or does not sit flush.
• Works with the dispenser housing components to maintain proper water/ice flow direction.

• Disconnect power to the refrigerator before beginning any work.
• Access may require removing the dispenser bezel or interior liner; save and reuse any mounting hardware if undamaged.
• Install with care to avoid overtightening fasteners or damaging adjacent plastic parts.

This assembly contains the evaporator defrost heater and temperature thermostat that remove frost from the evaporator coil to help restore normal cooling. Replaces failed defrost components to help the fridge complete defrost cycles and reduce ice buildup. What it does:

• Heats the evaporator during defrost cycles so accumulated frost melts away
• Uses a temperature thermostat to open/close the heater circuit at the correct temperature
• Commonly replaces failed defrost parts when frost builds on the evaporator or the refrigerator runs continuously
• Helps restore normal airflow and cooling when defrost cycle has stopped functioning

• One defrost heater and thermostat assembly

• Disconnect power to the appliance before starting any repair
• Handle the evaporator and fins carefully to avoid damage; keep electrical connections secure and dry
• Follow the manufacturer instructions for routing and mounting the assembly

This sealed-system compressor circulates refrigerant to cool your refrigerator, restoring normal cooling performance when the compressor fails. Designed to replace a failing compressor and help bring temperatures back to safe food-storage levels. What it does:

• Compresses and circulates refrigerant through the sealed refrigeration circuit
• Restores cooling when the compressor motor runs properly
• Commonly linked to symptoms like weak or no cooling, loud humming or clattering sounds, or a refrigerator that cycles continuously
• May be the cause if the appliance frequently trips a circuit breaker or shows hard-starting behavior

• Sealed-system work requires certified HVAC/refrigeration service and proper refrigerant handling per local regulations
• Disconnect power before beginning any repair; follow lockout/tagout practices
• Compressor replacement often requires system evacuation, brazing, and recharge — do not attempt unless qualified
• Use the identical replacement part number and follow OEM service instructions to avoid damage

This condenser fan blade is the rotating plastic blade that moves air across the condenser coils to help remove heat from the refrigerator. Replacing a damaged blade restores proper airflow for more consistent cooling. What it does:

• Spins on the condenser fan motor to circulate air over condenser coils
• Helps dissipate heat so the compressor and fridge run efficiently
• Can cause reduced cooling or higher temperatures if broken or missing

• Disconnect power to the appliance before starting any service
• Inspect the fan motor shaft and mounting for wear; replace motor if shaft is damaged
• Handle the blade carefully to avoid cracking; ensure blade is seated and secured before testing

This ice maker support is the mounting bracket that secures the freezer ice maker assembly, keeping it aligned for reliable ice production and delivery. Replaces a worn or broken support to restore proper fit and reduce ice-bin movement. What it does:

• Holds the ice maker in the correct position inside the freezer compartment
• Prevents the ice maker from shifting, tilting, or coming loose during operation
• Helps maintain proper alignment for ice dispensing and harvest cycles
• Can eliminate rattling or intermittent contact caused by a damaged support

• One ice maker support bracket

• Disconnect power to the refrigerator before beginning work
• Remove the ice maker and any obstructing trim to access the support
• Retain and reuse original fasteners unless replacements are specified
• Use basic hand tools; avoid forcing parts to prevent damage