Kbfa2derss01 Parts

Plastic evaporator cover for refrigerators. Installs over the evaporator coil in the freezer section. Replace if cracked, broken, or missing.

Short machine screw that secures refrigerator panels, trim pieces, and brackets. Replace when lost, stripped, or damaged to keep assemblies stable.

This door bushing fits on the refrigerator hinge/closer to provide a smooth pivot point and proper door alignment. Replacing a worn bushing reduces squeaks and binding and helps the door close and seal as designed.

• Provides a low-friction bearing surface between the hinge pin/closer cam and the door
• Helps maintain correct door height and alignment to the cabinet
• Promotes smooth door swing and reliable self-closing action
• Typical wear symptoms: squeaking or grinding, binding, door sag, or poor sealing

• Disconnect power and support the door before removing hinge hardware
• Note the order/orientation of hinge parts and any shims; lift off the door carefully
• Install the new bushing on the hinge pin or in the door as shown in your model's diagram
• Reinstall, level, and verify the gasket seals evenly all around

Replace cracked or broken pantry drawer glass cover in your refrigerator. Restores shelf surface above full-width deli drawer. Verify fit by model number.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Direct-replacement lower freezer bin for bottom-mount refrigerators. Restores organized storage when original is cracked, broken, or missing.

Color: White

Note: For Black, order WP67002721. For Grey, order W11245157. 

Support brace for 36-inch crisper drawer assembly. Restores secure mounting and alignment. Replace if cracked, broken, or causing drawer instability.

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

Black plastic plug that seals unused refrigerator vent openings. Replace if yours is cracked, broken, missing, or damaged to keep out debris.

Replacement hinge bushing that cushions and supports refrigerator door hinges. Install when original is cracked, worn, or missing to restore alignment.

Black plastic corner cover replaces damaged or missing exterior trim on your refrigerator. Restores finished appearance and protects edges from wear.

Vent plug insert for bottom-mount refrigerators. Replaces missing, cracked, or broken vent plugs. Installs in refrigerator cabinet openings.

Replaces broken or missing crisper drawer support pegs that secure and guide your refrigerator's crisper. Restores proper drawer alignment and support.

This is a protective cover that fits over refrigerator drawer compartments to provide a clear viewing surface and contain items. It prevents spills from reaching the drawer mechanism while allowing easy access to stored food items. Replace when the cover is cracked, cloudy, or no longer fits securely in place.

Directs airflow from the evaporator fan to cooling coils in your refrigerator. Replace if cracked, broken, or missing to restore proper air circulation.