Kbsd608ess Parts

This damper heater is the heater element used with the refrigerator air-damper assembly to help prevent frost and condensation buildup around the damper. Replaces a failed heater to restore proper damper operation and airflow. What it does:

• Warms the damper area to reduce ice and condensation that can block the damper
• Helps ensure the fresh-food and freezer compartments share airflow as intended
• Commonly replaced when frost or ice accumulates near the damper or when the damper fails to open/close smoothly
• Works as part of the damper/air control system; does not include the full damper housing or actuators unless specified

• Disconnect power to the appliance before replacing this part to avoid shock or injury
• Access may require removing interior panels or the damper housing; follow OEM instructions for your model
• Inspect the damper housing and actuator for damage or ice buildup when replacing the heater

This evaporator cover gasket seals the evaporator cover to the refrigerator cabinet, helping maintain proper airflow and reducing frost buildup behind the back wall. It restores a tight seal for more reliable cooling performance. What it does:

• Seals the evaporator cover to prevent air leaks that can cause frost or ice buildup
• Helps maintain consistent cold-air circulation in the freezer/refrigerator compartment
• Reduces chances of excessive frost, water pooling, or longer run cycles tied to air infiltration
• Supports normal defrost operation by keeping warm, moist air out of the evaporator cavity

• Disconnect power before servicing and allow the appliance to defrost if needed
• Remove the evaporator cover carefully; watch for sharp sheet-metal edges and retain fasteners
• Position gasket evenly around the cover mating surface; avoid stretching or creasing the seal
• If adhesive or clips are used, replace or reapply per OEM guidance to ensure a secure fit

Right hand side

Left hand side

Right hand side

A replacement receiver cover that protects and conceals the receiver/control housing, keeping internal components safe from dust and damage while restoring the appliance's finished appearance. Fits where the original receiver cover was installed. What it does:

• Covers and protects the receiver/control housing from dust, moisture, and accidental contact
• Helps secure wiring and small components inside the control area
• Restores the appliance's exterior appearance when the original cover is cracked or missing
• Can reduce intermittent issues caused by exposed connections when used as intended

• Disconnect power (unplug appliance or turn off breaker) before servicing to avoid electrical shock
• Remove the old cover by removing visible screws or clips; keep hardware if reusing is possible
• Align the replacement cover carefully and fasten with the original screws or clips; do not force parts into position
• If you see damaged wiring or mounting tabs, inspect further.

This replacement cover is a protective panel that helps shield internal components from dust and debris and restores the appliance's finished appearance. Installing the correct cover keeps parts protected and helps maintain safe, reliable operation. What it does:

• Protects internal electronics and wiring from dust, lint, and incidental contact
• Restores the appliance's exterior finish where the original cover was damaged or removed
• Helps prevent accidental access to moving or energized components
• Can reduce noise by covering openings near motors or fans

• One replacement cover

• Disconnect power to the appliance before beginning any work
• Handle edges carefully to avoid cuts and to prevent damage to the cover finish
• Verify orientation and fastener locations before tightening screws; do not overtighten

This small mounting retainer secures interior panels and components so covers, trims, or small assemblies stay aligned and stable. Replacing a broken clip restores fit and reduces rattles or loose panels for a neater appliance appearance. What it does:

• Holds trim, panel, or small component in place to maintain proper alignment
• Prevents vibration-related noise by keeping parts securely seated
• Replaces a worn, cracked, or lost factory clip to restore original fit
• Works where the original snap-in retainer or mounting tab is used

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access may require removing an exterior panel or trim; keep fasteners organized
• Use appropriate tools and gentle prying to avoid damaging surrounding parts

Color: Brushed Aluminum

This front cover is the molded outer trim piece that restores the appliance's appearance and protects internal components from dust and debris. It replaces a cracked, faded, or damaged front-facing panel to refresh the cabinet look. What it does

• Covers and protects internal components at the appliance front, preventing debris entry and shielding wiring and controls.
• Restores a finished exterior after impact, cracking, or cosmetic wear.
• Helps maintain proper airflow path and mounting surface for adjacent panels and controls.
• Commonly replaced when the front panel is cracked, warped, or broken.

• Remove power and disconnect the appliance before beginning any work.
• Access typically requires removing adjacent trim, bezels, or screws—retain hardware for reassembly.
• Align mounting tabs and fasteners; do not force the cover into place to avoid breaking clips.
• If clips or mounting hardware are damaged, replace them to ensure secure fit.