Kccg506rbl01 Parts

Color: White

Almond. Size: 13 oz. can. Acrylic appliance paint.

This switch nut secures a rotary control or switch to the appliance's front panel. Replacing a stripped or missing nut keeps the control stable so the knob turns smoothly and the shaft stays properly aligned.

• Clamps the switch/control to the panel to prevent movement or rotation
• Helps maintain correct knob alignment with dial markings
• Common symptoms: loose or wobbly knob, switch rotates in the panel, missing/damaged nut
• Often needed after service if the original nut is stripped or lost

• Disconnect electrical power before servicing
• Remove the knob and any decorative escutcheon; thread the new nut onto the switch bushing from the front of the panel
• Support the switch from behind while tightening; do not overtighten to avoid panel or switch damage
• Restore power and test control operation

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

This compressor starter engages the start windings so the refrigerator/freezer compressor can begin running. When the starter fails, the compressor may not start, leading to warm temperatures and clicking or brief humming from the compressor area.

• Provides a brief, high-current assist to the compressor's start winding to initiate operation
• Automatically disengages after startup so the compressor runs normally
• Common symptoms of a faulty starter: compressor won't start, repeated clicking, brief hum then stop, little or no cooling
• Helps prevent repeated, hard start attempts that can stress the compressor

• Disconnect power before servicing; wear appropriate PPE
• Access the machine compartment; note wire positions/orientation before removal
• Pull the old starter straight off the compressor pins; seat the new starter fully and reconnect wiring
• Avoid stressing refrigerant tubing; discharge it per safe procedures

This replacement stud is a factory-specified piece of hardware used to secure components in your appliance. Replacing a worn, stripped, or missing stud restores a solid fit to help reduce looseness and vibration. What it does:

• Provides a mounting point to fasten specified parts or panels
• Helps keep components aligned and secure during operation
• Replaces damaged, corroded, or missing original hardware
• Can resolve symptoms like loose parts, rattling, or misalignment where this fastener is used

• 1 stud

• Disconnect power; shut off water and/or gas supply if applicable
• Access the mounting location per your model's service information
• Start threads by hand to avoid cross-threading; tighten only until snug
• Reuse any original washers, clips, or nuts if required and in good condition

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

Color: White

This replacement control knob fits over the control shaft to select cycles, temperatures, or functions. It restores a secure grip and clear pointer when the original knob is cracked, stripped, or missing, returning smooth, accurate adjustments.

• Mounts to the control shaft to change and indicate settings
• Replaces knobs that are cracked, wobble, spin freely, or fall off
• Helps with symptoms like difficulty turning the control or inconsistent selections
• Restores a clean, finished look to the control panel

• Disconnect power (and gas, if applicable) before servicing.
• Pull the old knob straight off the shaft—do not twist the control stem.
• Align the D/flat/keyed insert with the shaft and press the new knob on until fully seated—do not force.
• If your original used a spring clip or set screw, transfer/adjust as needed.

Color: Black. Instruction sheet included.

Size: 8 x 1-1/4 inch.

Color: Almond

This Inner Door Panel forms the interior surface of the dishwasher door. Replacing a dented or corroded panel restores proper sealing and structural support for the latch and dispenser, helping prevent leaks and rattling during wash cycles.

• Creates the interior door surface and directs water back into the tub
• Provides mounting points for the detergent/rinse aid dispenser, door latch, and vent components
• Helps maintain a watertight seal when the door is closed
• Replace if rusted, cracked, warped, or if dispenser/latch mounts are broken; may show leaks at the door or unusual rattling

• Disconnect power and water supply before servicing
• Open the door and remove perimeter screws; support the outer door panel as you separate the panels
• Transfer the dispenser, latch, vent, and any insulation/gaskets from the old panel to the new panel
• Reassemble with even screw torque; verify door closes/seals and run a short test cycle to check for leaks

Color: Clear. This bulb is 40 watts and 120 volts.

This SPDT rocker switch restores dependable user control of a selected function on your appliance. Replacing a worn or intermittent switch brings back positive engagement and consistent operation. What it does:

• Toggles a single circuit between two positions to control a function
• Restores responsive on/off or selection input at the control panel
• Helps resolve no-response or intermittent operation when the switch is toggled
• Addresses a loose, sticking, or physically damaged rocker actuator

• Disconnect power to the appliance before servicing
• Access the control panel; note wire locations or take a quick photo
• Move wires to the new switch one at a time to maintain correct orientation
• Seat the switch securely in the panel, restore power, and test function

This bearing supports a rotating shaft or assembly inside the appliance, reducing friction for smooth, quiet motion. Replacing a worn bearing helps eliminate noise, restore proper alignment, and prevent damage to mating parts.

• Supports and centers a rotating shaft or hub
• Reduces friction and wear for smoother, quieter operation
• Helps maintain alignment of connected components
• Common failure symptoms: grinding or squealing sounds, vibration or wobble, rough/stiff or seized rotation, excessive play

• Disconnect power before servicing; shut off water or gas if applicable
• Note orientation and retaining hardware before removal
• Use proper tools (puller/press) to remove and seat the bearing squarely—avoid hammering
• Inspect shaft/bore and related seals or spacers; replace worn components before reassembly