Kceb208kss03 Parts

This small spring applies tension to hold an element in the correct position within the appliance, helping maintain reliable contact and stable operation. Replacing a worn spring can restore proper element support and performance.

• Provides push tension to keep the element seated and secure
• Helps prevent intermittent heating due to poor element contact
• Common signs include rattling, poor element stability, or intermittent heat

• Disconnect power and allow the unit to cool before service
• Access the element mounting area; note original spring placement
• Use needle-nose pliers to remove and install the spring carefully
• Inspect adjacent clips and wiring; replace damaged parts as needed

This replacement Thermostat Fix repair kit secures the thermostat assembly to help stabilize temperature sensing and restore consistent appliance performance. It's a small service part used when the thermostat mounting or retention hardware is worn or damaged. What it does

• Secures or replaces thermostat mounting/retention hardware to keep the sensor in proper contact
• Helps reduce intermittent temperature readings or cycling caused by a loose thermostat
• Restores stable thermostat positioning after vibration or wear
• Can stop noise or rattling related to a loose thermostat assembly

• One Thermostat Fix repair part

• Disconnect power to the appliance before servicing to prevent shock or injury
• Access the thermostat area per your appliance's service instructions; retain any screws or clips removed
• Replace the worn or damaged retention piece with this part and verify secure fit before reassembly

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

This switch bracket mounting seal replaces a worn or damaged seal that cushions and protects the door or control switch mounting area. It helps keep the switch assembly seated and reduces debris and moisture intrusion for reliable operation. What it does:

• Seals the switch bracket mounting area to protect the switch from lint, dust and moisture
• Helps keep the switch properly positioned for accurate door or control sensing
• Can prevent intermittent or failed switch contacts caused by contamination or misalignment
• Useful when replacing a brittle, torn or missing mounting seal during switch or door repairs

• Disconnect power to the appliance before starting any repair
• Remove the door or panel per service instructions to access the switch bracket area
• Fit the seal into the bracket groove or around the switch housing, ensuring full seating without stretching
• Inspect adjacent clips or screws and reuse or replace as needed; test the switch function after reassembly

This glass-ceramic cooktop surface replaces a damaged or cracked smooth-top cooking surface to restore a flat, easy-to-clean cooktop and maintain proper heating performance. It's the main cooking surface for smooth-top electric ranges. What it does:

• Replaces a cracked, chipped, or deeply scratched cooktop glass-ceramic surface
• Restores a flat, stable surface for cookware and helps ensure proper element alignment
• Helps prevent heat loss or uneven heating caused by damaged glass
• Keeps the cooktop easy to clean and maintain a finished appearance

• One glass-ceramic cooktop surface

• Installation requires removing the range cooktop assembly; follow the manufacturer service manual
• Handle with care — glass is fragile; wear gloves and eye protection during replacement
• Verify exact fit and part number match before installation

This surface heating element replaces a damaged or non-working top burner on electric ranges, restoring even heat for everyday cooking. It installs in the cooktop and connects to the range's terminal block for normal operation. What it does:

• Heats cookware on the cooktop when the burner control is turned on.
• Replaces elements that don't heat, heat intermittently, or heat unevenly.
• Helps eliminate visible burn damage or exposed wiring on the old element.
• Matches OEM fit and function for straightforward replacement.

• Disconnect power to the range at the breaker or unplug before servicing.
• Allow the old element to cool completely before removing.
• Handle terminals carefully; ensure tight, correct connections to the terminal block.
• After installation, restore power and test the burner through its full heat range.

This genuine replacement screw secures appliance components so panels, brackets, and assemblies stay tight and properly aligned. Replacing stripped, rusted, or missing hardware restores a solid fit and helps prevent rattles, shifting, or looseness over time.

• Fastens panels, brackets, and internal parts to maintain proper alignment
• Helps resolve issues caused by missing or damaged screws
• Restores secure mounting after service where original hardware is lost
• Use when threads are stripped or the screw head is damaged and won't tighten

• Disconnect power; turn off gas supply if applicable before servicing
• Match screw location and length to your model's parts diagram for correct placement
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug firmly but do not overtighten to prevent damage to mounting points

This hardware kit contains the small mounting parts needed to secure and support the appliance component. It provides replacement fasteners and brackets to restore proper fit and stability after service. What it does:

• Replaces worn or missing mounting pieces that cause loose panels or components
• Restores proper alignment and support for the associated assembly
• Helps stop rattling, vibration, or movement caused by missing hardware
• Matches OEM fit and function when used as a direct replacement

• Intended for technicians or experienced DIYers; inspect the kit before installation
• Use appropriate hand tools; tighten fasteners to manufacturer torque where specified
• Disconnect power and follow all safety procedures before servicing the appliance
• Replace only the parts shown for your specific model

This knob is an OEM part for Whirlpool ranges, designed to ensure a perfect fit and seamless operation within your appliance.

A faulty range knob can often result from wear and tear over time. Continuous usage may lead to the knob becoming loose or brittle, affecting its ability to effectively control the burner or set the desired temperature. Additionally, exposure to heat or spills can cause damage to the knob's internal components, impacting its functionality.

Symptoms of a malfunctioning range knob may include:

• Difficulty in turning or adjusting the knob
• Loose or wobbly knob on the range control panel
• Inaccurate temperature settings or inability to control the burner's flame intensity

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This foam seal is a flexible gasket strip that cushions and helps seal appliance openings to reduce leaks, drafts, and vibration. It restores a tight seal where original foam has deteriorated. What it does:

• Replaces compressed, torn, or missing foam that allows water, air, or heat to escape
• Helps stop minor leaks and reduces drafts that can affect temperature control
• Cushions panels and doors to reduce vibration and noise
• Restores proper contact between mating surfaces for improved performance

• Disconnect power and water before beginning repair
• Clean and dry mounting surface thoroughly; remove all old adhesive and residue
• Position seal carefully; trim with a sharp blade if necessary for a precise fit
• Use appliance-safe adhesive only if the original used adhesive; avoid over-compression when installing

The Vent Access Cover is an OEM part for Whirlpool cooktops. It is the rear ventilation cover located at the back of the oven cavity. This cover plays an important role in properly directing the exhaust of combustion gases and ventilating heated air outside of the home.

Causes of a bad vent cover can include damage from impact, warping due to overheating, or broken mounting points interfering with a tight seal. 

Symptoms of a bad vent cover include:

• Incomplete combustion of fuels resulting in efficiency and safety issues  
• Reduced airflow and ventilation compromising the oven function
• Gaps or openings that allow exhaust recirculation or intrusion of debris

 This OEM Whirlpool vent cover is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Cooktop is an OEM replacement part for Whirlpool cooktops. It acts as the durable and heat-resistant platform upon which you place your pots, pans, and cookware for cooking. This assembly includes the glass panel itself, which provides the cooking surface for the range, and other elements such as the metal frame or trim that surrounds the glass.

A bad glass main top can occur due to accidental damage, thermal shock, or general wear and tear. If you notice symptoms such as cracks, chips, or an uneven cooking surface, it may be time to replace the glass main top.

Symptoms of a bad cooktop include:

• Cracks or chips on the surface
• Uneven cooking temperature
• Difficulty in cleaning spills or stains

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Note: For Stainless model